The Usual Power Pin and Net Not Driven Errors...

[davefx]

Hello All...

I at least THOUGHT I knew how to draw a schematic,,, I wish someone could just look at my schematic and see where my ERC errors are coming from.. I tried the PWR_Flag thing, and the same solution everyone posted, but no sucess....

Dave

 

[Mattylad]

We cannot look at it if you do not post it here.

Or should we come and look over your shoulder? lol

 

[davefx]

I'm sorry but I'm trying to find an easy way to copy the error messages into this reply.. Is there a way for me to send my ERC report? and I'm afraid I'm a bit confused on where to upload PDF of my schematic?

 

[davefx]

Here we go..duh...lol
ERC report (7/16/2015 5:18:56 PM)

***** Sheet /
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (114.30 mm,39.37 mm): Pin 1 (passive) of component Q2 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (158.75 mm,33.02 mm): Pin 1 (passive) of component Q4 is unconnected.
ErrType(3): Pin connected to some others pins but no pin to drive it
@ (158.72 mm,28.50 mm): Pin 1 (power_in) of component #PWR09 is not driven (Net 14).
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (33.81 mm,26.16 mm): Pin 1 (passive) of component P1 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (33.81 mm,21.08 mm): Pin 2 (passive) of component P1 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (37.92 mm,26.06 mm): Pin 1 (power_out) of component #FLG014 is unconnected.
ErrType(3): Pin connected to some others pins but no pin to drive it
@ (49.53 mm,74.93 mm): Pin 1 (power_in) of component #PWR01 is not driven (Net 28).
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (36.22 mm,21.08 mm): Pin 1 (power_out) of component #FLG07 is unconnected.
ErrType(3): Pin connected to some others pins but no pin to drive it
@ (33.02 mm,49.53 mm): Pin 1 (power_in) of component U1 is not driven (Net 35).
ErrType(3): Pin connected to some others pins but no pin to drive it
@ (62.23 mm,86.36 mm): Pin 8 (power_in) of component U1 is not driven (Net 36).
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (186.69 mm,115.67 mm): Pin 4 (output) of component U1 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (163.83 mm,115.67 mm): Pin 5 (input) of component U1 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (186.44 mm,104.14 mm): Pin 2 (output) of component U1 is unconnected.
ErrType(2): Pin not connected (and no connect symbol found on this pin)
@ (163.58 mm,104.14 mm): Pin 3 (input) of component U1 is unconnected.

>> Errors ERC: 0

Now if I can master how to get a pic uploaded! lol.. Lets try this.... Yay! I think this will work



Again, I apologize for the redundant questions, but I did try to apply some of the posted solutions for these errors, but evidently I'm doing something wrong..

Dave

 

[davefx]

This, by the is for providing soft switching speed control to a vintage phase shifter clone (guitar effect) that I'm currently also attempting to layout on Expresspcb, which has the actual LFO, audio, and phase shift stages on it.

I just have an electronic technician diploma I earned in 1983.. I'm no engineer, but a musician and lover of music electronics.. I however have been learning PCB Cad starting with Windraft/Win board(anyone remember those?)... I really think this Kicad is cool if I can get a grasp on it .

I apologize for the windy post here, but I thought I would get that out in the open, so that all you wizards out there won't laugh too hard!

Dave

- - - Updated - - -

But THANK YOU Matylad and BigDog and everyone else in advance too!

Dave

 

[davefx]

Well I guess I'll stick with ExpressPCB then..