Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

How to read/write data from 24c512 interfacing with pic16f887?

Status
Not open for further replies.
8051 has open drain I/O with weak pull-up, PIC has push-pull I/O. Bit banging with I2C works respectively different with PIC, must operate TRIS register. Why don't you use PIC hardware I2C interface (MSSP)?
 

Read/write data with Interfacing 24c512 with pic16f887

Eeprom adress needs 16 bits (if range over 255) => Adresse HI , Adresse LO .. to send to EEPROM

mikroC and 16F877 example .. uses unsigned int Adr

Code:
void Write_Byte_To_24LC256(unsigned int Adr, unsigned char cx)
{

I2C1_Start();
I2C1_Wr(EEPROM_32K_ADR );      // write
I2C1_Wr(Adr>>8);    // send data (data to be written)
I2C1_Wr(Adr& 0x00FF);
I2C1_Wr(cx);    // send data (data to be written)
I2C1_Stop();
Delay_ms(5);
 }

unsigned char Read_Byte_from_24LC256(unsigned int Adr)
{
unsigned char c3;
I2C1_Start();
I2C1_Wr(EEPROM_32K_ADR );  // write
I2C1_Wr(Adr>>8);    // send data (data to be written)
I2C1_Wr(Adr&0x00FF);
I2C1_Stop();
I2C1_Start();    // I2C1_Repeated_Start();
Delay_ms(1);

I2C1_Wr(EEPROM_32K_ADR+1 );  // Read
c3=I2C1_Rd(0u);    // data to be read)
I2C1_Stop();
return c3;   
}
 

I did both of this but it is not working. Is there any thing i can do so that i can read/write data and also pages from c 24c512?

- - - Updated - - -

This code is also not working. This is for 8051 but i want to covert in to use for my application then use. Plz show me correction that i have to do in this.

Code:
sbit SDA = PC^4; // Serial Data Address Input/Output
sbit SCL = PC^3; //        Serial Clock

//=****************************************************************************

void send_to_mem(char s_address, char s_data)
 {
   
    start_EEPROM();             // sending start condition to eeprom 
    send_EEPROM(0XA0);     // A0 = 10100000 = sending device address word for write
    acknowledge();
    send_EEPROM(s_address); // sending data address
    acknowledge();
    send_EEPROM(s_data);   // sending data 
    acknowledge();
    stop_EEPROM();              // sending stop condition to eeprom
        acknowledge();
        wait(100);
          
 }
//============================================================================
char get_from_mem(char s_address)
 {
    char i = 0;
//-------dummy write seq----+ word address------------------------------------
    start_EEPROM();             // sending start condition to eeprom 
    send_EEPROM(0XA0);     // sending A0 = 10100000 = device address word for write
    acknowledge();
    send_EEPROM(s_address); // sending data address
    acknowledge();
//----------------dummy over----------------------------------------------------


    start_EEPROM();
    send_EEPROM(0XA1);     // sending A1 =10100001 = device adress word for read
    acknowledge();
    i = get_EEPROM(); // sending data 
    acknowledge();
    stop_EEPROM();              // sending stop condition to eeprom
        acknowledge();
    return(i); 
 }
//============================================================================
void send_EEPROM(char s_byte)
 {
    char temp = s_byte;
    char i ;

        
    for(i = 7 ; i >= 0 ; i--)
    {
 
        temp = s_byte;
        temp = temp >> i;
        temp = temp & 0X01;

     
        if(temp == 0)
            SDA =   0;
        else
            SDA =   1;

                SCL   =   1;
        wait(40);
        SCL   =   0;
           
    }
 }
//============================================================================

char get_EEPROM()
 {
    char temp, temp_h, i;
    temp = 0;
    temp_h = 1;        

    SDA = 1;    // making SDA as input pin for microcontroller
           SCL = 0;

    for(i = 7; i >=0 ; i--)
    {
        SCL = 1;
        if(SDA == 1)
        {
            temp = temp | temp_h<<i ;                      
        }
        wait(40);
                SCL = 0;
    }
    
    SCL = 0;
    return(temp);
 }
//============================================================================
void start_EEPROM()
 {
    SDA     =   1;
    SCL    =   1;
    wait(40);
        SDA     =   0;
        SCL    =   0;  

 }
//============================================================================
void stop_EEPROM()
 {
    SDA     =   0;
    SCL    =   1;
    wait(40);
    SDA     =   1;
    SCL    =   0;  
 }
//============================================================================
void acknowledge()
 {
         SCL = 1;
           wait(40);
        SCL = 0;
 }
//============================================================================
void wait(int i)
 {
    for(;i>=0;i--)
           {
           }
 }
 
Last edited by a moderator:

hello,

Adresse must be 16 bits wide ..

Code:
void send_to_mem(int s_address, char s_data)
 {
   
    start_EEPROM();             // sending start condition to eeprom 
    send_EEPROM(0XA0);     // A0 = 10100000 = sending device address word for write
    acknowledge();
    send_EEPROM(s_address>>8); // sending MSBaddress
    acknowledge();
     send_EEPROM(s_address & 0x0FF); // sending LSB address
    acknowledge();
    send_EEPROM(s_data);   // sending data 
    acknowledge();
    stop_EEPROM();              // sending stop condition to eeprom
        acknowledge();
        wait(100);
          
 }
 

Can you plz explain sendEEPROM() and getEEPROM() briefly as i have posted earlier in post4?
 

I am not able read data from get_EEPROM(). Every time it reads only 0XFE.
Code:
char get_EEPROM()
 {
    char temp, temp_h, i;
    temp = 0;
    temp_h = 1;        

    SDA = 1;    // making SDA as input pin for microcontroller
           SCL = 0;

    for(i = 7; i >=0 ; i--)
    {
        SCL = 1;
        if(SDA == 1)
        {
            temp = temp | temp_h<<i ;                      
        }
        wait(40);
                SCL = 0;
    }
    
    SCL = 0;
    return(temp);
 }

Kindly tell me the changes that i have to do in this.
 
Last edited by a moderator:

hello,

Datasheets explain all details..but you need to take some time to read it .
Others can help you, but don't do this elementary job, instead of you .

you simplify too much the EEPROM reading
have a look on page 9 of AT24C512 eeprom datasheet
fig 5 Random read and fig 6 sequential read ..
and work around this .
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top