Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by yelloww_

  1. yelloww_

    Looking for datasheet of MST9010

    Re: mst9010 I'm also looking to find MST9010. (ALLDATASHEET.CO.KR - dosen't have it)
  2. yelloww_

    Looking for ISO7637 standard

    Re: ISO7637 REQUIRED ISO_7637-2_2004 full attached
  3. yelloww_

    ISO 15765 Network Layer protocal

    iso 15765 network layer anyone has some info on 15765?
  4. yelloww_

    Test watt hour Standard IEC 62052-11

    61000-4-2 Hi, I would like to get the IEC 61000-4-2 Standard, anyone? Yel
  5. yelloww_

    QAM Demodulator - BCM3510

    Just to add.. The performance of the BC*3510 VSB demodulator is not really good compare to 3517 & 3520. Yel
  6. yelloww_

    QAM Demodulator - BCM3510

    Hi, The BC*3510 from BC* is an old chip. Not really recommended for new design. Please look at the BC*3517 or BC*3520 instead. If you really need the info on the 3510. Please send me your question and I'll answer them My BC*3510 datasheet is watermarked with my information. So I can't send...
  7. yelloww_

    A pair of ICs , that does AES/EBU <-> I2S conversion?

    i2s aes/ebu Hi, Look for Crystal (Cirrus Logic) and AKM components Look for an AES/EBU/SPDIF Receiver and Transimitter SPDIF is the consumer version of the AES/EBU. regards Yelloww
  8. yelloww_

    Temperature Testing Chamber

    Hi Guys, I would like to build/design my own homemade climatic chamber to do some electronics pre-qualificaion and testing. The typical pcb size is around 10inx10in. A typical project can easily dissipates up to 45W. Ideally the chamber temperature range should be around 0oC to 60oC Does...
  9. yelloww_

    [REQ]Low cost DC-DC converter solution

    very low cost..very good....see www.anachip.com in Taiwan..a whole famility of DC-DC.. regards Yelloww
  10. yelloww_

    HD RECEIVER LST-3100A service manual

    Does someone has the service manual or the electronic schematics for the LST-3100A from LG ?? cheers Yelloww
  11. yelloww_

    Information about H.264 decoder design

    Re: H.264 decoder Texas instruments with their DM642 DSP can decoder any standard. WM9, h.264, Mpeg2... But the IP core for it is quite expensive... Do you have a technology in mind? More hardware ? I know that Xilinx is working on a H.264 solution for thir FPGA... let me know.....what you...
  12. yelloww_

    Looking for routing schema for FF1148 BGA package

    Re: fanout BGA FF1148? Hi, You'll need a lot of PCB layers to fanout this thing Look at Xilinx website, they have similar package and they recommend how to fanout this king of beast.... www.xilinx.com regards
  13. yelloww_

    CATV Distribution Amplifier (for cable app)

    Do you know any opamp who can do the job instead of transistors ? Opamp will be easier to work ..... cheers Yelloww
  14. yelloww_

    CATV Distribution Amplifier (for cable app)

    Hi, Anyone already design this...I would like to distribuate 16 CATV feeds. The amplifier must works at 54Mhz to 900MHz. Gain must be around x16 (~30dB) Any advice will be appreciated !. regards
  15. yelloww_

    What if I want my power supply conform to UL authentication?

    Re: What if I want my power supply conform to UL authenticat It's a quick question....but with very very long answer........ First you need to determinate where the power supply will be used for ? Consumers electronics ? IT equipments ? others ? After you know that....Purchase the UL standard...
See more

Part and Inventory Search

Back
Top