Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by yazid

  1. Y

    stepper motor controller code using C language

    hi..i have a coding to control speed for stepper motor using assemble languange..but now..i want a coding by C language to control the speed of the stepper motor by vary the frequency...
  2. Y

    how to interface CAN controller(MCP 2510) to pic16f877a

    can any one tell me how to interface CAN controller(MCP 2515) with pic16f877a controller?
  3. Y

    stepper motor driver using UCN5804

    assembly language to control stepper motor i olredy make the pwm coding using assembly language in PIC16f877 to move my stpper motor..how i want to transfer from hex value to rpm?
  4. Y

    Recommend a motor speed control circuit

    motor speed control can anybody give me a source code 4 pwm using assembly languagu for pic16f877?
  5. Y

    stepper motor driver using UCN5804

    5804 and 555 vs step motor can i control the speed of the stepper motor if i use ULN2003 as a driver for stepper motor?
  6. Y

    Information about CAN bus system

    Re: CAN bus system which part in CAN bus that u know?i want 2 use CAN i my project final year to control the stepper motor..do you hav any information about that?actually my project title is 'MODULAR STEPPER MOTOR CONTROLLER USING CAN'....tq
  7. Y

    stepper motor driver using UCN5804

    driver ic 5804 price i olready did the circuit for the stepper motor,but the motor cannot run..there hav a voltage drop at the output from LM7805 to the motor.the actual voltage for the motor is 5 volt,but the output from the Lm7805 is 2.35 volt only
  8. Y

    stepper motor driver using UCN5804

    ucn5804 pin i already check the variable voltage regulator LM317 at www.farnell.com hav a lot of LM317 there..so,i dont know which one that must i select..can u giv me suggestion?
  9. Y

    stepper motor driver using UCN5804

    lm317 stepper driver but i'm not very good in programming.....
  10. Y

    stepper motor driver using UCN5804

    ucn5804 controller diagram ok..thnks watermelon and kishore2k4...for programming i want 2 control the speed and position..wat must i do?which one i must chose?C++?Basic pro?or assembly language?
  11. Y

    stepper motor driver using UCN5804

    ucn5804 price thanks kishore.. i already got the circuit diagram..my stepper motor is 4volt and 0.95A.how i want to get the 4 volt supply.is there have voltage regulator for 4 volt?
  12. Y

    stepper motor driver using UCN5804

    ucn5804 logic circuit but i not use timer 555,i use pic16f877 and the UCN 5804
  13. Y

    stepper motor controller using Controller Area Network (CAN)

    mcp2251 anybody can help me to get the circuit for stepper motor controller using Controller Area Network (CAN).i'm using: - unipolar stepper motor 6 wire - UCN5804 as a driver - PIC16F877 as a controller - MCP2251 as CAN Transceiver - MCP2510 as a CAN controller thaks u...
  14. Y

    stepper motor driver using UCN5804

    ucn5804 any body can help me to get the circuit and information for stepper motor driver using UCN5804? thanks...
  15. Y

    stepper motor with microstepping

    i need to do microstepping motor controller using CAN(Control area network) as my final year project..may somebody help me?how to do microstepping motor driver?can i use all type of stepper motor to become microstepping motor?thank u..
See more

Part and Inventory Search

Back
Top