Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by vamanan

  1. V

    Need used FPGA board

    Hi, I am looking for a used FPGA board. Any body have and willing to sell in US, please reply me. Thanks & Regards, Vamanan
  2. V

    Help in ORCAD needed

    Hi, I am making a circuit in ORCAD 16.6. I created a hetrogenous part library with 2 parts inside. I saved the library after creation. Now if I want to add 2 more sub circuits in that library, how can I do that?. Please help. Vamanan
  3. V

    [SOLVED] Refrigerator Defrost time

    For an air conditioner, the defrost timing varies from 15 to 30 minutes. Probably you may use the same timing for a refrigerator.
  4. V

    [Req.][AC current limiter circuit]

    Hi, I have an AC circuit. I want to limit the current to 1A to the load. But during error condition 10A can flow to the circuit. But I want to limit the current to 1A. Can anybody give some ideas how to implement the same. Thanks Vamanan Kutty
  5. V

    CAN bus messages in AC powerline

    Hi, I want to send CAN bus messages through 110V AC Power line. Can anybody help me in deciding whether it is possible or not ?. If possible can you suggest suitable Power Line modem to be used. I am unable to get the information from google. Regards, Vamanan Kutty
  6. V

    Power Source switch IC

    Hi All, I have two 220V power sources. I want to power my device with this. If One power goes off , the device need to switch to the other 220V source. Is there any IC's to do this?. Help me regarding this.
  7. V

    UART isolation using Optocoupler

    Hi, I am using 8051 for serial communication. It talks with another microcontroller at TTL level. So I think there is no need for MAX232. Am I correct ?. Is it enough if I connect tx of miconA to rx of moconB and rx miconA to tx of miconB. Is it like this or I need to connect some other way?. If...
  8. V

    Doubt in VC++[Display a byte in text box]

    Dear All, I am getting a byte value (Say 0x80) through USB Port and storing this byte in a variable. I want to display this byte value in a text box. ie) the text box should display 80. I am unable to do it. Please help me. Regards, Vamanan Kutty
  9. V

    ESD Test in flow meter design using MSP430

    Hi All, I recently designed a flow meter using MSP430 and did some EMI/EMC test. When ESD test was done, the unit reset immediately when High voltage was in contact with the body which was earthed. Give me a solution how to resolve the problem. I have a 30 multiplexed seven segment display in...
  10. V

    [SOLVED] Embed a picture into PCB silkscreen layer

    Dear friend, download from **broken link removed**
  11. V

    visual basic interfacing with PIC microcontroller

    visual basic interfacing Do you mean serial interfacing through RS-232 protocol ?. If this is the case then you have to use MSComm control in Visual basic.
  12. V

    [SOLVED] Embed a picture into PCB silkscreen layer

    convert bmp2pcb download You can use a DXP-add on called Klipper. Otherwise you can go for a free software bmp2pcb.exe. You can google it to download. This tool convert mono bmp files to protel format, which you can cut and paste in your dxp files.
  13. V

    Good schematic drawing software

    schematic software For schematic capture I suggest Orcad/Cadence. For PCB go for Protel
  14. V

    Need FPGA development kit ....

    Dear Karthik, I messged you. But I didnt get any reply. I am interested in buying from you. Give your mail id. I will mail you. Or mail me vamanan_2005@india.com
  15. V

    VHDL Simulator[Need Info.]

    vhdl simulator I want to know what are the VHDL simulators available. I want to learn VHDL. So please suggest VHDL simulators(only). Advance Thanks.
See more

Part and Inventory Search

Back
Top