Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by sgharagoz

  1. S

    A very simple Hspice question

    Hi Erikl, I don't think adding CLM would help me. In fact if I consider that, it will make the drain current even more than I calculated. The velocity saturation is more plausible but I have used this model card before and I am very sure that hand calculation should be very close to the actual...
  2. S

    A very simple Hspice question

    Hi guys, I have got a very simple netlist that I trying to simulate in Hspice: MN1 VCC Gat 0 0 CMOSN L=360n W=360n VDD VCC 0 DC 1.8 Vgs Gat 0 DC 1.43 .OP 1us .END The model used is 0.18micron TSMC. In the model K' is defined as...
  3. S

    counter with similar states

    Thanks for your input. What I dont understand is that if you draw the FSM, 0110 is a state between the other two states, which means on the next clk cycle, the next state could be either 0011, or 1100!!! Is there any way we could differentiate them?
  4. S

    counter with similar states

    Hi there, How do you design a counter that has a similar state such as, 1100,0110,0011,0110,1100,...... Thanks
  5. S

    ADPLL textbook, paper, ....

    Hi there, I am new to PLL and dont know where to start! I read Razavi's book to some extent but there is no mention of ADPLL whatsoever. Do I need to understand PLL first before I start reading about ADPLL? I need to understand ADPLL very quickly so I would really appreciate if you guys can...
  6. S

    Installing Cadence in Linux Mint [question]

    Hi there, Did you get my message? Was it helpful? Cheers
  7. S

    Installing Cadence in Linux Mint [question]

    Sorry I almost forgot to reply! I can send you the procedure! send me your email! By the way If your cadence has NCSU libraries then we may have a problem installing it, Since mine doesn't have. https://www.eda.ncsu.edu/wiki/NCSU_EDA_Wiki Cheers
  8. S

    starting up Modelsim in ubuntu 12.10

    Hi, I have installed the Modelsim 10.1 on ubuntu 12.10, but I don't know how to startup the program! I would love it if you could help me Thanks
  9. S

    Installing Cadence in Linux Mint [question]

    I have installed cadence 6 on ubuntu! but I assume the procedure should be the same!
  10. S

    HSPICE Avanwaves problem

    Thanks a lot dude! for some strange reason I couldn't do it when I tried couple of times Cheers!
  11. S

    HSPICE Avanwaves problem

    I am using 2007 HSPICE Is it possible to plot multiple graphs from different simulations by only using Avanwaves once?I mean not closing or opening a new Avanwaves program? Cheers!
  12. S

    Is it possible to do a AC simulation for a switching circuit?

    I try to explain my problem better! I have two files each has an opamp in it! they are identical. If I run AC Monte carlo simulation for the first file can I use the exact variations to do a monte carlo simulation for the second file? Thanks a lot for all your suggestions!
  13. S

    Is it possible to do a AC simulation for a switching circuit?

    Lol, I have to work on that to make it rhythm better!
  14. S

    Is it possible to do a AC simulation for a switching circuit?

    My problem is more severe than that! I have to do monte carlo simulations to check the intra-die variations! So every time I run the monte Carlo it generates a new set of variable which makes my life more miserable!
  15. S

    Is it possible to do a AC simulation for a switching circuit?

    Thanks Keith I have a switching circuit controlling the current sink of an Op-Amp. Of course during the time when the gates are turing on and Off Op-Amp doesn't work once everything is steady Op-Amp operates. I tried this HSPICE but gain were not right! Cheers
See more

Part and Inventory Search

Back
Top