Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by savan

  1. S

    Decoder Cadence ADE Simulation problem

    Re: Decoder Cadence ADE Simulation problem(I did not see this error never before)) Hi Raj Have you been able to solve this issue?
  2. S

    IEEE Papers in English

    Hello Folks! I am browsing through IEEE papers and I am little amused to see that some IEEE papers are published in 'Chinese' or 'Turkish'(i.e not in English) I really need to read those papers is there a way I can get those in English? Google Translator in not much of help here with its...
  3. S

    is it possible to install orcad 9.1 and cadence 16.3 in same system?

    I was wondering what is actually difference between two? OrCAD is from company Cadence that's I am sure! then what exactly is this Cadence 16.3 or whatever?
  4. S

    Problem with simulation in ORCAD CIS Capture using PSPICE

    I am designing DVCC block on CIS capture (proposed by Elwan and Solimon) I am facing following error after I save my design and ORCAD closes afterwards. Any hints suggestions? Thanks in advance Similar post was also started but has not been solved yet! please help!
  5. S

    Spice Model Parameter for DDCC

    I am trying to simulate 'Novel CMOS Differential Voltage Current Conveyor' by 'Elvan and Solimon'. IEEE paper by them mentions to use '2um SCN Process Parameter through MOSIS' I need this parameter to simulate the circuit. I have been to MOSIS website but it gives parameter below 0.5um Can...
  6. S

    [SOLVED] Different Technologies for VLSI Design

    Something that concerned me to Ponder over the Technology was this! All of my design on software(Electric VLSI) has been designed with MOCMOS(scale=300.0nm, foundry:MOSIS) Does this make sense to any one of you? if yes please enlighten me! I know that latest technology is 25nm and 35nm is its...
  7. S

    [SOLVED] Different Technologies for VLSI Design

    There are different technologies available for VLSI Design like 35nm, 50nm, 75nm, 100nm. I am following the default Technologies of my Software Electric VLSI. Can anybody throw some light on what diff these technologies make and all! Thanks I am exploring this with google but I will...
  8. S

    What is Reachable Chip Area?

    I am working on a project on VLSI Optimization and in that I have to make comparision among Reachable CHIP AREA versus Clock Rate? I am exploring this with google but I will appreciate the views of fellow members! Further request is it would be highly helpful it is answered considering you are...
  9. S

    [SOLVED] What are Soft Processors? is 8085 a soft processor?

    Thanks it helped! I am wondering if I have Spartan-6 FPGA board then can I program it for any processor(like 8085 and 8086) or there are limitation that 'ONLY SOFT PROCESSORS' can be implemented on it!
  10. S

    [SOLVED] What are Soft Processors? is 8085 a soft processor?

    What are Soft Processors? is 8085 a soft processor? Can anybody enlighten me about this? Thanks!
  11. S

    measurement for Power consumption/loss in a circuit in Electric VLSI

    I have a circuit in whic I want to measure power consumed/loss using Electric VLSI but I haven't been able to find any such option can anyone be of help?
  12. S

    Fourier Series Elementary Question

    Why do u feel J to be necessary in Vector Space and there is nothing like imaginary part is must in Vectors! You can express even Square wave in terms of Fourier Series
  13. S

    MATLAB and VLSI Physical Design

    Can MATALB be used to draw physical design of simple component/circuit? I was going through diff software which can be used to design circuits! I just bumped onto a thread which mentioned MATLAB so I am curious if anyone knows I would be grateful in knowing your experience with these two! Many...
  14. S

    thread for VLSI designers -Which VLSI Design tool do u use!

    Is anybody uses Electric VLSI tool for VLSI layout and schematic designs? If you dont then then which VLSI design tool do u use and why do u use that(advantages of that tool!) Thanks
  15. S

    [SOLVED] doubt regarding 8fo4/16fo4

    Apologies! Brian you were right it meant nothing! It was just a notation author used! Many Thanks!
See more

Part and Inventory Search

Back
Top