Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
1. so i need to buy 9amps or higher amps
2. whether if i connect 23 bulbs parallely with 12v/ 9amp transformer means the brightness of bulb will get diminish ?
regards
hi
if one 12v/5w bulb need 0.416 amp means, if i need to connect 23 bulbs parallely means i need to multiply this amp with 23(no of bulbs) , if so i need to to get 12v/9amp transformer for 23 bulbs to connect parallely, is it correct?
or i need to get higher rating of amp..
regards
how to calculate VA rating and current rating for bulbs of above mentioned ratings. tell me formula because i need to connect around 50 bulbs parallely.
regards
i need to connect 5 small bulb parlely . rating of one bulb is 12-16 v and 5W. I need to connet it in normal house supply of 230v. tell me how choose the transformer rating for this using formula so that it will be useful for me to connect more bulbs by parallel. Also suggest me circuit to...
hi
i dint got bluetooth module, i need to buy it, i need with low cost .i don't know how to write uart code using ccs compiler, if u got any uart code kindly post also suggest which module to buy..
regards
hi
i need to transmit data from PIC controller to moble using bluetooth. which module is cheap to use and easy to code . im using ccs compiler to write code for that. kindly suggest for me
regards.
hi
Im trying to read values from IMU sensor , but while trying to compile it shows error, while clicking any error it always goes to #include <18f4550.h> line..
the error occurring while compiling are
my code is
#include <18F4550.h>
#fuses NOWDT,HS,NOPROTECT,NOLVP
//#fuses...
hi
code wrote for gyro sensor shows -1 -1 -1 in lcd, it is not changing when i change my sensor. my code is#Include <18f4550.h>
#fuses NOWDT,HS
//#fuses HS,MCLR,NOWDT,NOPROTECT,NOLVP,USBDIV,PLL5,CPUDIV1,VREGEN
#use delay(clock=4000000)
#use i2c(Master,sda=PIN_B0,scl=PIN_B1)
#define...
hi
I have got Pololu minIMU-9V2, in which I'm trying to read gyroscope values. When i connect my sensor its always showing X=-1, and when i disconnect my sensor its showing X=10223 0r X=10877. Since it has got pull up resistor i didn't connect external pull up resistor.
my code is #Include...
i have tested with i2c bus scanner , in that it shows device address for all the 3 sensor in hyperterminal. i dont know how to read it as u mentioned above.. check whether the code as correct or not because have tried by changing the registers in the code..
regards
i have written code to read only accelerometer values from IMU9v2 sensor(combination of accelerometer, gyroscope and magnetometr), but it is not showing any result in serial terminal..
my code is:
#include <18f4550.h>
#fuses HS,NOWDT,NOPROTECT,NOLVP
#use delay(clock=4000000)
#use...
i need to transfer data from micro controller to mobile using blue tooth also i dont know which module will be easy and low coat.. im using PIC 18f series and ccs compiler to write coding, can any one send me the code for my project.
hi
i need to interface bluetooth module to store data for my project, can any one guide me to do that with low cost module. i have came to know that some one mentioned that having working code for this, kindly can u upload that. i saw that in below link
https://www.edaboard.com/threads/167257/
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
