Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by rajbabu

  1. R

    Make file basics for compilation

    Hi, What is meaning of: $(subst .c,.o, $(LIB_SOURCES)) in make file. How this recipe compiles the .c files included in LIB_SOURCES?
  2. R

    [SOLVED] make coomand in Batch file

    Can you elaborate it more with example.
  3. R

    [SOLVED] make coomand in Batch file

    what is meaning of in batch file %MAKEDIR%\cmd\make %1 %2 %3 %4 %5 %6 %7 %8 %9 What are this numbers 1,2, 3 etc.
  4. R

    [ARM] DS2782 Capacity issue

    No, Because what that IC do, Its ICs function to calculate capacity as characterization we by storing value into EEPROM, then we can read from EEPROm directly. If i am wrong please correct me. Because this i understood from datasheet.
  5. R

    [ARM] DS2782 Capacity issue

    Hi, thanks for suggestion. From this page what you want to show. I already stored parameters for battery in EEPROM.
  6. R

    [ARM] DS2782 Capacity issue

    Hi, I want to measure capacity of battery foe application, For this i used DS2782 fuel gauge IC. I am able to communicate with this IC , and getting voltage , current, average current. But not able get Capacity. I also programmed EEPROM as per calculation. Can any body help?
  7. R

    SIM 900 got stuck in SEND sms command

    HI, I connected SIM900 modem to PC and sending commands through Hyper terminal. I am able to call. but i try for send sms it got stuck after entering Message. and i wanna us it again so i have to power off it and again power on it. i am trying like this AT enter response is OK...
  8. R

    SIM900 sending SMS with roaming SIM fails fatally

    I am facing the same problem did you found any answer.
  9. R

    [SOLVED] How to use GPS for distance calculation.

    Dear friends, I wanna calculate distance using GPS module, I am able to find the coordinates i mean, Latitude and Longitude. But not able to find distance between one predefined coordinate and one from GPS. Rajbabu...
  10. R

    GH 311 Ultrasonic power up delay???

    Hi, I am also facing same problem. If find it then reply me.
  11. R

    what is X5 in potyo2 ICD2 clone

    What is X5 in Potyo2 ? Rajbabu
  12. R

    potyo2 icd2 clone components

    One more thing i want to know what for X5 connector is:?: Rajbabu
  13. R

    potyo2 icd2 clone components

    Thanks for reply, I searched a lot but still not able to find the exact difference between PICkit2 and ICD2. Please provide me ckt and firmare for PICkit2 so i can i try it also. Thanks Rajbabu
  14. R

    potyo2 icd2 clone components

    Thanks for suggestion, Till now i was using JDM programmer which uses COM port, but now using laptop which does not have COM port so i switched to this, one more reason is that now i want use debuging tool also. Exactly i dont know difference between PIKKIT2 and ICD2. Can you give detailes or...
  15. R

    potyo2 icd2 clone components

    Hi friends. I am trying to make ICD2 clone potyo2. But i have some confusion regarding components. 1. R41 resistance value is 0.47, It means it is short or it is miss written 2. 170uF inductor, it is not available in market, can i use close value tot this. Thanks in Advance Rajbabu
See more

Part and Inventory Search

Back
Top