Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
You can use a hex File Editor, and a PC based VB facility to dump the bitmap onto NAND or NOR flash, Whichever the one you have.
And, You can verify if the bitmap has been properly loaded into the External Flash, by checking the *.map file.
- - - Updated - - -
You can use a hex File Editor...
I am writing a code on lpc1788 ARM Cortex M3. I came across a strange warning when I tried to configure the ports as GPIO. Despite of the warning, the code works absolutely fine, but to learn why this warning come, I am putting forward this post here. Following is the code that I have written...
meter reading using RF??
Try and specify what you want to design in detail. Then only you can get the resources.
I have seen a project that was designed to read the meter reading and disply it at a far end using ZigBees. It was named Wireless Multimeter using ZigBee. It didnt make any sense...
Hello Friends.
I have been trying to program my ATMega8 using a parallel port programmer (DB25) with winAVR. I am having problems with makefile. Whenever I try to progrm my chip, it says "No rule make target all". Please help me out. And, please mail me a makefile for parallel port programmer...
Hello Everyone!
I am working on a project that requires a Wireless Tx-Rx.
The project that I'm working is a Railway Engine (a demonstrative model) that would be running on DC supply of 6-24Volts.
What I want to do is, the TX mounted at the Signal post should send a signal to the Locomotive...
Hello Everyone!
I am working on a project that requires a Wireless Tx-Rx.
The project that I'm working is a Railway Engine (a demonstrative model) that would be running on DC supply of 6-24Volts.
What I want to do is, the TX mounted at the Signal post should send a signal to the Locomotive...
Hello Friends.
I intend to make a Landmine Detector Robot.
Planning to control it using RF rather than it being wired. (ZigBee will be used)
I had first thought to use a Metal Detector for that. But it may generate False-Alarms.
Then, I read about a GPR based Landmine Detector. The fellow...
Hello Friends.
I intend to make a Landmine Detector Robot.
Planning to control it using RF rather than it being wired. (ZigBee will be used)
I had first thought to use a Metal Detector for that. But it may generate False-Alarms.
Then, I read about a GPR based Landmine Detector. The fellow...
Hello Friends.
I intend to make a Landmine Detector Robot.
Planning to control it using RF rather than it being wired. (ZigBee will be used)
I had first thought to use a Metal Detector for that. But it may generate False-Alarms.
Then, I read about a GPR based Landmine Detector. The fellow...
Hello Friends.
I intend to make a Landmine Detector Robot.
Planning to control it using RF rather than it being wired. (ZigBee will be used)
I had first thought to use a Metal Detector for that. But it may generate False-Alarms.
Then, I read about a GPR based Landmine Detector. The fellow...
Hello. Can any one please tell me, if there is any sensor that can sense the Sunlight Intensity. I want such a sensor to sense the intensity of sunlight at a place with that at some other place. Can that be done?
Hello. I am looking forward to make a bot. It would carry a Solar Panel, a battery that will be charged using the Panel and a seperate battery for the driving of the bot.
The bot should roam around a limited area and track down the area with maximum solar intensity. At such a place, it should...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.