Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by gghhh

  1. G

    [SOLVED] ERROR(SPMHCS-1): Symbol is missing a refdes.

    Thanx all i got it done.
  2. G

    [SOLVED] ERROR(SPMHCS-1): Symbol is missing a refdes.

    Actually I am getting this error in PCB editor and not in capture. Here is the Screen shot. - - - Updated - - - And here is the USB which Im trying to draw the PCB foot Print.
  3. G

    Question abt SPI0 and SPI1

    Hello every1, I have question, I am using this uc AT32UC3A3256 and it has two SPI; SPI0 and SPI1. My question is if I have selected SPI0 can I take output from SPI1_MOSI??? Thanx in advance.
  4. G

    [SOLVED] ERROR(SPMHCS-1): Symbol is missing a refdes.

    Hello all, I am trying to draw the pcb foot print of mini usb type b. When I save the symbol it says ERROR(SPMHCS-1): Symbol is missing a refdes. Can some1 please help me. Thanx & Regards Here is the zip file with .dra and an image of the usb mini type b.
  5. G

    [SOLVED] Question about SPI and Microcontroller

    Thank you very much.
  6. G

    [SOLVED] Question about SPI and Microcontroller

    It fits the requirements, the biggest being cost... My supervisor can order it for free of cost. - - - Updated - - - How can I have 3 different SPI_CLK using AT32UC3B0256 it says in the doc that i can have 4 SPI connected but HOW? http://www.atmel.com/devices/at32uc3b0256.aspx?tab=parameters...
  7. G

    [SOLVED] Question about SPI and Microcontroller

    yes its for medical application and its mandate that i have to use zl70101.
  8. G

    [SOLVED] Question about SPI and Microcontroller

    Re: Question abt SPI and Microcontroller Cannt I use SPI for Wireless transmission?
  9. G

    [SOLVED] Question about SPI and Microcontroller

    Re: Question abt SPI and Microcontroller Asic is an application specific and Zarlink (ZL70101) is for wireless transmission of data and Accelerometer(LIS331DL). ASIC works at 1.4Mhz frequency, All i have to do is to send the data from Accelerometer and ASIC thru wireless and that too one at a...
  10. G

    [SOLVED] Question about SPI and Microcontroller

    Hello all, I have a small doubt I have three devices that is connected to a microcontroller. 1. ASIC (1) 2. Zarlink (1) 3. Accelerator(3) NOTE: 1,1,3 are the no. of devices I am using. So a micro-controller should have min. 5 SPI to connect or just 3 SPI is enough?
  11. G

    Where can I find ATUC256L3U part for Cadence orCAD schematic.

    Do i have order from the Atmel?
  12. G

    Where can I find ATUC256L3U part for Cadence orCAD schematic.

    Where can I find ATUC256L3U and LIS331DL part for Cadence orCAD schematic. Hello all, I am looking for ATUC256L3U and LIS331DL. I cannot find in cadence orCAD library. Any Idea where can i download?
  13. G

    [SOLVED] question about microcontroller LM3S9C97

    Hw abt i use TMS320F28069 instead of LM3S9C97?
  14. G

    [SOLVED] question about microcontroller LM3S9C97

    Even though there are from the same manufacturer?
  15. G

    [SOLVED] question about microcontroller LM3S9C97

    Just one last question. My friend wrote the code for MSP430F2416 and can I also use the same code in LM3S9C97? They are both from Texas Instrument.
See more

Part and Inventory Search

Back
Top