Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by GeekWizard

  1. G

    PCDE and RCDE for WCDMA

    Hi all, What is PCDE (Peak Code Domain Error) and RCDE (Relative Code Domain Error) for a UMTS signal? Also, how can I measure RCDE using a standard MXA N9020A? Many Thanks!
  2. G

    Why do satellite use microwaves?

    Hello, I know higher the frequency more likelihood of causing resonance in similar size molecules, thus increasing abosorption chances. Then why do satellites communication use so high frequencies (L, K band etc.) ? I want to know why these pass through the ionosphere and not abosrbed...
  3. G

    RF/Microwave Jobs in Canada ?

    So 1. Ontario any ideas on no. 2? Would help me in my planning ! Thanks...
  4. G

    salaries for embedded engineer

    Correct me if I am wrong but I have seen North America the best for engineers' salaries followed by other EU countries like Germany, France and then UK,Spain etc. I was surprised by some ppl.s comments on salaries in scotland. Do engineers get paid more there as compared to england?
  5. G

    RF/Microwave Jobs in Canada ?

    Hi there, Which areas have most RF/Microwave jobs in Canada ? I know of the techological hubs like Ontario and Waterloo but I am wondering if somone can give me more specific information on RF jobs .. Many Thanks !
  6. G

    Salary Survey for Canadian Engineers

    It seems that average salaries are only slightly better in Canada than here in UK.. I was wondering howz the jobs opportunities for RF Engineers in Canada now.. After nortel bankruptcy, confidence is a bit low and it seems only RIM is hiring .. Any thoughts/comments?
  7. G

    RF Engineer for mobile phones - Skills

    - What is VSA? Is it different from a normal spectrum analyser? - Are there any links to detail design inside a cellular phone? - Does anyone know a specific research area for next generation smartphones? Thanks
  8. G

    RF Engineer for mobile phones - Skills

    rf skills Hello .. I have an interview at Nokia for a 'RF Engineer' position. I have knowledge of generic RF stuff but I was wondering if anyone can specify more on What kind of RF skills are really needed for such a position ? Many Thanks
  9. G

    Tracking system - GPS or RF ?

    Is it true that GPS needs a direct line-of-sight link with the antenna and satellite ? If it is so, I was wondering how can a GPS based system work to track containers kept inside a vehicle ? Many Thanks.
  10. G

    Tracking system - GPS or RF ?

    rf beacon tracking Dear all, I need to make a presentation on what factors to consider in designing a tracking system embedded in the Cash-In-Transit products. I have googled such systems and also on this board, most of the people suggest a GPS-GSM embedded system i.e. finding the location...
  11. G

    Designing an Embedded Tracking System

    What about a tracking system based on GSM and an RF beacon rather than GPS? I read somewhere that it is more accurate - not sure how though ?
  12. G

    Designing an Embedded Tracking System

    Dear all, I need to make a presentation on what factors to consider in designing a tracking system embedded in the CIT products. I have googled such systems and also on this board, most of the people suggest a GPS-GSM embedded system i.e. finding the location through a GPS module and...
  13. G

    Help for "Error : does not hold value outside clk edge&

    Re: Help for "Error : does not hold value outside clk e Here is the part of code that deals with the signal 'S_PLLValid'. I tried to mark the signal as bold but apparently it doesnt highlight under the code tag, so I've indicated using arrows. signal S_PLLValid:STD_LOGIC...
  14. G

    Help for "Error : does not hold value outside clk edge&

    Hello, I am trying to compile a VHDL code written by another person. I am getting this error for a number of signals. The Quartus Help file apparently does not provide any details on this error. Can anyone help what the reason is and how can the error be corrected?
  15. G

    VHDL : 'Integer' range and its use

    Hello, I know that integer's range is upto 2^31 - 1. But does this condition apply to the every number in the equation that would result in an integer ? e.g. signal factor : integer ; begin factor <= (2**48) / (300E6) ; factor_bin <= conv_std_logic_vector (factor,20); 2**48 is...

Part and Inventory Search

Back
Top