Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by electtron

  1. E

    SFP transceivers - part numbers, power consumption

    sfp gg Hi everyone, With respect to the SFP transceivers can you please clarify the following a) Does SFP transceivers that support 56 Kbps, 64 Kbps and 2 Mbps are available. If so can you please suggest the part numbers b) What is the difference in power consumption between the modules...
  2. E

    SFP transceivers - part numbers, power consumption

    SFP transceivers Hi everyone, With respect to the SFP transceivers can you please clarify the following a) Does SFP transceivers that support 56 Kbps, 64 Kbps and 2 Mbps are available. If so can you please suggest the part numbers b) What is the difference in power consumption...
  3. E

    IGBT series connection - how to turn them on synchronously?

    igbt series Hi, When IGBTs are connected in series (for high voltage switching, the voltage rating of a single IGBT would not be sufficient and hence they would be connected in series, so that the voltage gets divided across these IGBTs), how can they be turned ON synchronously. How is the...
  4. E

    Synchronous control for IGBT series connection

    igbt series Hi, When IGBTs are connected in series (for high voltage switching, the voltage rating of a single IGBT would not be sufficient and hence they would be connected in series, so that the voltage gets divided across these IGBTs), how can they be turned ON synchronously. How is the...
  5. E

    Power Supply - help needed with voltage and current

    Re: Power Supply Help It happens when to try to connect a load that draws more current than that could be supplied by the power supply. Either try increasing the current limit set on your power supply or connect a load thta draws lesser current
  6. E

    [SOLVED] Circuit simulation software

    Hi, Try SI metrix. It's freely downloadable and a very good tool
  7. E

    What cable to use for 12 VDC @ 15 Amps 5meters?

    Re: What cable to use ? Hi.. you can use a cable with 10 AWG
  8. E

    12 layer PCB stack up

    12 layer pcb stack up Hi everyone, What is best stack up for a 12 layer PCB. Does the following hold good Type Layer SIGNAL - Layer 1(Top) GROUND - Layer 2 SIGNAL - Layer 3 SIGNAL - Layer 4 GROUND - Layer 5 POWER - Layer 6 POWER - Layer 7 GROUND - Layer 8 SIGNAL - Layer 9 SIGNAL - Layer 10...
  9. E

    Which is better for DSP implementation, FPGA or TMS320?

    Re: FPGA or TMS320 I would say go for TMS320 for DSP applications. Since the architecture of TMS320 suits the complex algorithms of DSP
  10. E

    IRIG-B Implementation

    Hi all, I want to implement an IRIG-B circuit in one of my projects. But I was unable to understand the IRIG-B standard and had no clue on how to implement it. Can any one please help me in this regard
  11. E

    FPGA coding for RSTP(IEEE 802.1w)

    Hi, Can anyone please tell me whether it is feasible to implement Rapid Spanning Tree Protocol(RSTP) conforming to IEEE 802.1w in a FPGA. If anyone did so can you please send me the details..... Thanks in advance
  12. E

    Looking for resources about designing PI filters

    Hello everyone, I need to design a PI filter that can be used to isolate the noise between supply lines and a pcb board.And I know nothing about pi filters?? Can anyone help me out in this regard in designing the pi filter?? Also please suggest some links on pi filters design..... Thanx in...
  13. E

    How to design pi filters?

    Hello everyone, I need to design a PI filter that can be used to isolate the noise between supply lines and a pcb board.And I know nothing about pi filters?? Can anyone help me out in this regard in designing the pi filter?? Also please suggest some links on pi filters design.....
  14. E

    How to design pi filters?

    Hi, Can anyone please explain about pi filters? How to design them and what are considerations to be taken while designing them??
  15. E

    What is Miller Capacitance in a MOSFET?

    What is Miller Capacitance in a MOSFET? and how do you calculate it from a typical MOSFET datasheet???
See more

Part and Inventory Search

Back
Top