Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Well, I connected a battery charger to the battery with another multimeter in series to measure the current on the + wire and then clamped the same wire with the UT201 and the measurements were almost exact. So if this clamp meter can measure this DC current like the other meter then I'm very...
Thank you FvM.
Just one question...what is my clamp meter measuring when I put it around a +DC source wire if it does not support DC measurements? I have some readings that are little bit oscillating 0,3A up and down. Hmm..:thinker:
Hi to all. I have bought this clamp meter https://uni-trend.com/UT201.html# thinking that it would measure DC current but it does only AC. When I put the clamps around a DC source wire it however shows some results. I'm interested, are those readings accurate and is there a way to measure the DC...
To Brad: Here is the inside of the charger. I think it is very basic and I have not found any automatic taper setting so it could come to chuckey's idea trying to connect it to the solar controller.. :wink:
To Frank: Do you think that it is ok to set the charger to 24V quick or slow?
To...
Thnx Sunny, I'm not much in the techtalk. Can you please tell me if it is possible to use my cheap Einhell charger paired with some -of the shelf-ready to buy- electronic device to protect these batteries from overcharging or can I throw it away? 8-)
Hi chuckey, sorry if I didn't mention it before but I have already a solar charger: https://www.ebay.co.uk/itm/310857447913?_trksid=p2060778.m2749.l2648&ssPageName=STRK%3AMEBIDX%3AIT but now I need to use my grid charger when there is no sun. So, can you please give me a link to this kind of...
Hello
I have this charger: **broken link removed** and a solar battery bank made of these batteries: https://www.osibatteries.com/p-1052-enersys-powersafe-sbs-60-sealed-lead-acid-battery-120v-510ah.aspx connected in a way to get 24V 200Ah.
I know that this charger is not suitable for charging...
Hi
I'm proud to announce that the advice Klaus gave me is running smoothly without any distortions and with a big grin on my face.. :-)
Here is how I connected the resistors. Bare in mind that the original 10k are very small and hard to mess around without making some damage on the board in my...
Thanks Guru for the resistor thing. As I can see from the picture above every input has one 10k resistor before entering the amp. I have bridged these channels after the resistors to see what happens and it worked but there were some distortions in the mid frequencies. So if I follow your...
Ok guys, as I thought this went out of my knowledge level. Let's forget this amp. and the whole idea of stereo to mono story.:-|
I put it in a simple question. Is there a mono amplifier on the market with stereo input that runs in the 3-6V voltage range and that has something like 2-4W power...
Thank you Guru for this quick reply. I have been scratching my head for days about this problem. I have to mention that at Dealextreme it says 2*8ohm so I thought I have the right speaker. However I have a 4 ohm speaker of the same kind and it is not a problem to connect. I have tried the 4 ohm...
Hello
First I'm not in electronics so much and please have this in mind if you going to give me some advice.:wink:
I have this little amp:
VMA2012 - 2x3W Class D Audio Amplifier
and I need to connect only ONE speaker to it because my project requires it. I have read some proposals here...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
