Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ahmedsalah00

  1. A

    whats the difference in application of ferrite core transformer

    As I understand you want to buy a ready-made transformer rather than winding it manually. would you supply more data about its part number ? The first thing that comes to mind is that the fifth leg is a center-tap !
  2. A

    Signal conditioning Question

    Hi everybody I need to find an instrumentation amplifier to drive an ADC . the amplifier input is the triangular voltage signal from 1 KHz to 1 MHz shown in the figure. I need to keep this signal without distoration while multiplying by a gain of 3 . Any suggestions ?
  3. A

    Large Signal Frequency Response

    Thanks so much for your feedback. It is much appreciated. :-)
  4. A

    Large Signal Frequency Response

    so , we may think of figure 20 as the SOA (safe operating area ) of work ?
  5. A

    Large Signal Frequency Response

    Hi I just need to understand the curve entiteled "Large Signal Frequency Response' in the AD620 Instrumentation amplifier datasheet. my concrete questions are: 1- What are the dashed verticle lines ? G=100 and G=1000 2- What does the phrase "BW limit" indicate in the curve? and why ? please...
  6. A

    Core losses for DC biased ferrites

    Hello all, I am trying to calculate the ferrite core losses resulting from the an alternating current biased by a certain DC value. the core is ETD29 and the material is Epcos N27. What is the value of flux density B that can be used in the Manufacturer Pv curves? Bmav , Bav or ∆B ? the...
  7. A

    controlling speed ac motor with 8051

    I think V/F ratio must be kept constant for frequencies over the nominal frequency. But for lower speeds (lower frequencies) , V can be kept constant while changing the speed by changing the frequency. Ahmed Salah
  8. A

    controlling speed ac motor with 8051

    Hello which kind of AC motor is it ? if it is an induction motor , you can not control its speed by controlling the voltage as its output torque will decrease dramastically. However , you can control its speed by changing the frequency you should read something about space vector pulse width...
  9. A

    Why I see 10A current pulse?

    Re: Current pulse What about IRF740 ? VDSS 400V Rds(on) 0.55Ohm max ID 10A trr Reverse Recovery Time ––– 360 ns, IF = 10A Qrr Reverse RecoveryCharge ––– 2.9 µC di/dt = 100A/µs you can use the selection guide of international rectifier to choose the best transistor according to your load...
  10. A

    How to interface an AV camera to a microcontroller?

    camera interfacing yes the idea is implemented in so many applications. For example Olympus C-750 can be interfaced and contrlled by its USB connection. there are numerous camera's and CCD's in the market. Good luck in your search
  11. A

    Simultating Microcontrollers

    This topic is discussed before, Have a look at this: and and
  12. A

    which PCB designer program to use?

    I used protel 1.0 , protel 1.5 , protel 99 , protel DXP and PCAD. I think Protel DXP is a very powerful tool for PCB and circuit design . it has a compatible spice engine for circuit simlation. I didnt like PCAD because it lacks libraries , you have to define the foot print for each component...
  13. A

    CRC - error detection/correction

    Hello , I know that CRC (in which a polynomial is used) is a tool for error detection. but it is not used for correction. I dont have a big experience so my answer may be wrong.
  14. A

    selecting a pull up/down resistor value

    for which application ? would you draw a circuit if possible ? In general , you have to select the value of the resistor so that the current doesnt excced a certain value.
  15. A

    which Embedded Processor?

    Thanks yasser , it seems that you are from Egypt, do you have any idea about the distributors of this in Egypt ?
See more

Part and Inventory Search

Back
Top