Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
How do I find the channel coefficients for a two input two output system ? I mean to say that there are two transmitters and two receivers which means that my channel matrix will be a 2*2 one ... any help is appreciated. thanks
hi guys
i want to knw how we can give external trigger to a pic18 circuit board.
i am using mikro c for code and proteus simulation. if i give a trigger on one of the pins, it should glow the led's connected to some other port.
the program works fine with mikro c and proteus.. but when i test...
hello guys!!
anyone knows how to write into mmc from pic!!.... i need to knw it urgently
i am using a pic18f4550... i have interfaced an rtc ds1307 with it, now i need to write that time into a memory card ?? ,...i m really stuck.........how do i go about doing it ?...i looked at the examples...
Re: How to read data from MMC using PIC microcontroller ???
were you successful in the mmc and mc interfacing?? even i need to do the same urgently..to send data from pic to mmc... and i am still a beginner, so dont have a proper idea about pic and mmc interfacing
if the microcontroller can operate in the 3.3v range, then there is no problem as sd card will work on 3.3v.. but if it is a 5v like pic18f4550..then you need to use a voltage divider circuit... use the help section in mikroc... the circuit is also given, search for mmc section in...
hey, pappu_sam.., i think it is easier to code using mikroc.. as mmc is a part of my project, and i am using mikroc for one of the other parts.. i would prefer to do it in mikro c.. but dont think it wil make a big difference once we get the hex file...
we can first test it in proteus vsm.. and...
thank you so much to all...
after two months of struggle, i managed to write data into rtc and read data from it. it usually takes much lesser time for experts...but i am still a beginner, and doing a project for the first time.
my next challenge is to store the date and time into a memory...
hi all,
i am a beginenr in pic programming, and i very urgently need to know how to write data from a pic port into a mmc... i have very less idea abt mmc and pic programming.. i am using a pic18f45550 controller in order to do this.... but am not getting idea how to start the process....it...
hi all, can u pls tell abt the procedure you used to store data from the pic microcontroller into the memory card using mikroc... i am a beginner and i dont knw anything about mmc..!!.. help will be greatly appreciated
hey, doraemon, cud u pls tell how u wrote data into card...and give a sample...
hey pappu_sam..even i want to interface a mmc to pic18 controller (pic18f4550),.. i just want to write data from controller to the mmc... i think it is possible using mplab...but may be, mikroC could be easier... i am also looking out for a sample code to write into mmc...
hi,
i need to transfer data from pic18f4550 to a mmc/sd card. i have just started working on pic18f, so dont have a deep understanding of the pic18....can anyone suggest how i go about storing data from a port in pic18 to a memory card... i need to store the data on the occurance of an external...
Thank you, I shall try it.
But only the header files are there in the attachment, how do i use it ?
do i use a software like mikroc or sumthing?
Anyways thank you.
Hi,
I am doing this for the first time and getting stuck. cAN anyone please help me out in this -
I need to interface a pic microcontroller (preferably pic18) with a real time clock- either using ds1307 or any other RTC chip.
My e-mail id is adi265ster@gmail.com
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
