VOLTMETER using pic18f4550....Help needed

i need help in this code///nothing is displayed on LCD //




#include <p18F4550.h>
#define lcdport PORTB
#define rs PORTAbits.RA0
#define rw PORTAbits.RA1
#define en PORTAbits.RA2


void lcd_ini() ;
void lcdcmd(unsigned char) ;
void lcddata(unsigned char);
void adc_con(unsigned int) ;
void adc_init();
void DELAY(int time);

unsigned char data[20]="ADC OUTPUT=";
unsigned int digital_out[10],avg_output=0,temp;
unsigned int i=0;
void main()
{
TRISCbits.TRISC0=0;
TRISA=0; // Configure RA0 as input pin
PORTA=0;
TRISB=0;
PORTB=0; // Configure Port B as output port


lcdcmd(0x38); // Configure the LCD in 8-bit mode, 2 line and 5x7 font
lcdcmd(0x0E); // Display On and Cursor Off
lcdcmd(0x01); // Clear display screen
lcdcmd(0x06); // Increment cursor
lcdcmd(0x86); // Set cursor position to 1st line, 1st column
lcddata('w');

while(data!='\0')
{
lcdport=*data; // Call lcddata function to send character one by from 'data' array
i++;
}

ADCON1=0xCE; // Make RA0/AN0 pin as analog pin (Other pins remain to be digital I/O)
ADCON0=0x81; // Select Channel0 & ADC off
ADCON2=0x8A; // Left justified, 2TAD acquiciation time, Fosc/32 clock option
ADCON0bits.GO=1; // Enable ADC

while(1)
{
temp=0;
for(i=0;i<10;i++)
{
ADCON0bits.GO=1; // Start A/D conversion
while(ADCON0bits.DONE=1); // Wait until conversion gets over
digital_out=((ADRESL)|(ADRESH<<8)); // Store 10-bit output into a 16-bit variable
DELAY (20);
temp=temp+digital_out;
}
avg_output=temp/10; // Take average of ten digital values for stablity
adc_con(avg_output); // Function to convert the decimal vaule to its corresponding ASCII
}
}




void adc_con(unsigned int adc_out)
{
unsigned int adc_out1;
int i=0;
char position=0xC3;
for(i=0;i<=3;i++)
{
adc_out1=adc_out%10; // To exract the unit position digit
adc_out=adc_out/10;
lcdcmd(position);
lcddata(48+adc_out1); // Convert into its corresponding ASCII
position--;
}
}


void lcdcmd(unsigned char cmdout)
{
lcdport=cmdout; //Send command to lcdport=PORTB
rs=0;
rw=0;
en=1;
DELAY(50);
en=0;
}


void lcddata(unsigned char dataout)
{
lcdport=dataout; //Send data to lcdport=PORTB
rs=1;
rw=0;
en=1;
DELAY(50);
en=0;
}

void DELAY(int time)
{
int k=0,j=0,r=0,a=0;
for (k;k<time;k++)
for (j;j<25;j++)
for (a;a<25;a++)
for (r;r<25;r++);
}

Hello!

If you just publish your code, it's very difficult to help you. You should explain
what goes wrong (in which function, at which line, and what exactly goes wrong).

Dora.

ADCON1=0xCE; // Make RA0/AN0 pin as analog pin (Other pins remain to be digital I/O)

Click to expand...

You are using RC0 as your ADC input and configured RA) for ADC input. Make the changes. You have connected RA0 to LCD.