sample programs for the pic controller

[fasihuddin]

i am using pic16f32ka304 micro controller and i need the sample programs for ADC,PWM initializations...

 

[premswaroop]

sample program for adc in pic32

#include <plib.h>

// Configuration Bit settings
// SYSCLK = 80 MHz (8MHz Crystal / FPLLIDIV * FPLLMUL / FPLLODIV)
// PBCLK = 80 MHz (80MHz / 1)
// Primary Osc w/PLL (XT+,HS+,EC+PLL)
// WDT off
// Other options are don't care
//
#pragma config FPLLMUL = MUL_20, FPLLIDIV = DIV_2, FPLLODIV = DIV_1
#pragma config FPBDIV = DIV_1
#pragma config POSCMOD = HS, FNOSC = PRIPLL
#pragma config FWDTEN = OFF

#define SYS_FREQ (80000000L)

unsigned int channel4; // conversion result as read from result buffer
unsigned int channel5; // conversion result as read from result buffer
unsigned int offset; // buffer offset to point to the base of the idle buffer

int main(void)
{
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states and
// enable prefetch cache but will not change the PBDIV. The PBDIV value
// is already set via the pragma FPBDIV option above..
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);

// configure and enable the ADC
CloseADC10(); // ensure the ADC is off before setting the configuration

// define setup parameters for OpenADC10
// Turn module on | ouput in integer | trigger mode auto | enable autosample
#define PARAM1 ADC_FORMAT_INTG | ADC_CLK_AUTO | ADC_AUTO_SAMPLING_ON

// define setup parameters for OpenADC10
// ADC ref external | disable offset test | disable scan mode | perform 2 samples | use dual buffers | use alternate mode
#define PARAM2 ADC_VREF_AVDD_AVSS | ADC_OFFSET_CAL_DISABLE | ADC_SCAN_OFF | ADC_SAMPLES_PER_INT_2 | ADC_ALT_BUF_ON | ADC_ALT_INPUT_ON

// define setup parameters for OpenADC10
// use ADC internal clock | set sample time
#define PARAM3 ADC_CONV_CLK_INTERNAL_RC | ADC_SAMPLE_TIME_15


// define setup parameters for OpenADC10
// set AN4 and AN5 as analog inputs
#define PARAM4 ENABLE_AN4_ANA | ENABLE_AN5_ANA


// define setup parameters for OpenADC10
// do not assign channels to scan
#define PARAM5 SKIP_SCAN_ALL

// use ground as neg ref for A | use AN4 for input A | use ground as neg ref for A | use AN5 for input B

// configure to sample AN4 & AN5
SetChanADC10( ADC_CH0_NEG_SAMPLEA_NVREF | ADC_CH0_POS_SAMPLEA_AN4 | ADC_CH0_NEG_SAMPLEB_NVREF | ADC_CH0_POS_SAMPLEB_AN5); // configure to sample AN4 & AN5
OpenADC10( PARAM1, PARAM2, PARAM3, PARAM4, PARAM5 ); // configure ADC using the parameters defined above

EnableADC10(); // Enable the ADC

while (1)
{
while ( ! mAD1GetIntFlag() )
{
// wait for the first conversion to complete so there will be vaild data in ADC result registers
}

// the results of the conversions are available in channel4 and channel5

offset = 8 * ((~ReadActiveBufferADC10() & 0x01)); // determine which buffer is idle and create an offset

channel4 = ReadADC10(offset); // read the result of channel 4 conversion from the idle buffer
channel5 = ReadADC10(offset + 1); // read the result of channel 5 conversion from the idle buffer

mAD1ClearIntFlag();
}

return 0;
}

 

[horace1]

have a look at
Microcontrollers Project Examples
**broken link removed**