Matlab code for Cell Phone Jammer

Status
Not open for further replies.

Adil Israr

Full Member level 1
Joined
Sep 5, 2008
Messages
97
Helped
5
Reputation
10
Reaction score
4
Trophy points
1,298
Activity points
1,918
matlab using cellphone jammer

Hello, I am Telecom student and doing my final year project on Cell Phone Jammer, i need Cell Phone Jammer simulation in matlab,,plz help me as soon as possible.Thanks
 

matlab code for cell phone jammer

first tell me the exact function of "Cell Phone Jammer" . how it works ?
 
cell phone jammer

I am basically working on dual band Cell phone jammer.
I will jam two GSM bands i.e; GSM 900 & GSM 1800.
It will cosists of two parts:
1)IF section
2)RF section
In the IF section following components will made;
a)Triangular wave generator (Sweep generator)
b)Noise generator
c)Mixer
d)Clamper
RF section contains following parts:
a)Two VCOs(output frequencies equal to downlink frequencies of the bands).
b)The power amplifier;

This jamming techniques is DENIAL of SERVICE:
In this technique, the device transmits a noise signal at the
same operating frequency of the mobile phone in order to decrease the signal-to-noise ratio
(SNR) of the mobile under its minimum value. This kind of jamming technique is the
simplest one since the device is always on.

Added after 3 minutes:

this is for GSM 1800. The output frequency is 1785-1900 MHz and the output
power is up to 5 dBm.

this is for GSM 900. The output frequency is 925-970 MHz and the output
power is up to 8 dBm.

Plz help me as soon as possible.
 
functioning of cellphone jammer

that jammer operating in denial of service mode may not actually require a matlab code. the circuit elements are purely analog unless you are working with a programmable VCO. but i can assure you that the jammer would still function without any programming....the VCO is the most important part but hard to find. I actually developed a circuit but upto now I've been unable to obtain a VCO. can you refer me somewhere or to junk or radio equipment, cellphone e.t.c?
 

hiya I would like to ask about Cell Phone Jammer simulation in matlab, could you please send to me the simulation to elghawari@yahoo.com

Added after 35 seconds:

as soon as possible.
 

Matlab code for cell phone jammer

%%%%%%%%%%%%% The main.m file %%%%%%%%%%%%%%%
clear;
% Parameters of the Gaussian filter:
n1=10;sigma1=3;n2=10;sigma2=3;theta1=0;
% The amplitude of the noise:
noise=0.1;
[w,map]=gifread('lena.gif');
x=ind2gray(w,map);
filter1=d2gauss(n1,sigma1,n2,sigma2,theta);
x_rand=noise*randn(size(x));
y=x+x_rand;
f1=conv2(x,filter1,'same');
rf1=conv2(y,filter1,'same');
figure(1);
subplot(2,2,1);imagesc(x);
subplot(2,2,2);imagesc;
subplot(2,2,3);imagesc(f1);
subplot(2,2,4);imagesc(rf1);
colormap(gray);
%%%%%%%%%%%%%% End of the main.m file %%%%%%%%%%%%%%%

---------- Post added at 05:23 AM ---------- Previous post was at 05:22 AM ----------

%Initialization D=1 (D = interleaving depth)
clear;
Ts=1/1e3; % tx rate = 10k bps
NA=10000;
A=floor(rand(1,NA)+0.5);
%A=randint(1,NA);
input=A;
G=[1 0 0; 1 0 1; 1 1 1];
k=1;

N=length(channel_output);
SNRdB= -10:5:20;
SNR=10.^(SNRdB/10);
Counter=zeros(1,length(SNRdB));
loop=0;

%************************************************* **************
% AWGN + fading *
%************************************************* **************
Fd=66; % Actual fading rate
fm=round(Fd*NA*Ts);

%Generate two inputs of 1 x N matrix
xin=randn(1,(NA+2)*3);
yin=randn(1,(NA+2)*3);

%Loop for all values of frequencies and truncate at just before f=fm
for f=1fm-1)
filter(f)=1.5/(pi*fm*sqrt(1-(f/fm)^2));
end
for f=(fm-1)NA+2)*3
filter(f)=0;
end

%Inputs of the filter is multiplied with the filter transfer function
xout=xin.*filter;
yout=yin.*filter;

%Perform inverse Fourier Transform on both output
xifft=real(ifft(xout));
yifft=real(ifft(yout));

% normaliation so that E{R^2}= 1 / in Watt = 0 dB
std_x=std(xifft);
std_y=std(yifft);
xifft=xifft/std_x/sqrt(2);
yifft=yifft/std_y/sqrt(2);

%Sum the square the of the IFFT and take the square root of it
rx=sqrt(xifft.^2+yifft.^2);

%************************************************* ***************
%Calculate for all value of SNRdB in AWGN + fading
%************************************************* ***************
loop=0;
for b=sqrt(SNR) %b is the signal level
loop=loop+1;
dfad=0;
for n=1NA+2)*3 %n = no of bits
x=randn;
t=channel_output;
if t>=0.5
a=b*rx;
r=a+x;
if r<0
dfad=dfad+1; % error has occured, increase counter
Df=0;
else
Df=1;
end
else
a=(-b)*rx;
r=a+x;
if r>0
dfad=dfad+1;
Df=1;
else
Df=0;
end
end
Counterf(loop)=dfad; % w/o decode
end
output=viterbi(G,k,Df); % E is output of decoder
zf=0;
v=1;
for v=v:1:length(A);
if xor(input(1,v),output(1,v))==1
zf=zf+1;
end
end
Counter_wcf(loop)=zf;
end% loop for signal (b) in AWGN + fading


%plot simulation in AWGN + fading without coding
Pef=Counterf/N;
%semilogy(SNRdB,Pef,'b');
%hold on;
%plot simulation in AWGN + fading with coding
Pe1f=Counter_wcf/NA;
save D1_66SNRdBPe1fPef
%semilogy(SNRdB,Pe1f,'b'); %D=1 no interleaving
%hold on;

---------- Post added at 05:25 AM ---------- Previous post was at 05:23 AM ----------


:shock:
clear;
Ts=1/1e3; % tx rate = 10k bps
NA=10000;
A=floor(rand(1,NA)+0.5);
%A=randint(1,NA);
input=A;
G=[1 0 0; 1 0 1; 1 1 1];
k=1;

N=length(channel_output);
SNRdB= -10:5:20;
SNR=10.^(SNRdB/10);
Counter=zeros(1,length(SNRdB));
loop=0;
 
Re: matlab using cellphone jammer

Hello, I am Telecom student and doing my final year project on Cell Phone Jammer, i need Cell Phone Jammer simulation in matlab,,plz help me as soon as possible.Thanks

my problem is exactly same as tours..if u have already got the solution please contact me asap...thanx
 

Hi... I would like to ask about Cell Phone Jammer , could you please send to me the final report to east_one@hotmail.com
as soon as possible.
thanks alot
 

Status
Not open for further replies.
Cookies are required to use this site. You must accept them to continue using the site. Learn more…