Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

is it my gerber output from allegro true?

Status
Not open for further replies.

asadi.siyavash

Member level 4
Joined
Feb 14, 2013
Messages
68
Helped
2
Reputation
4
Reaction score
2
Trophy points
1,288
Activity points
1,769
Hi
I am new in allegro and it is my first gerber output, it is really simply board but I don't know how I can create properly output?
so I attached my works if is it possible help me. and also suggest me simple and right application guide for creating gerber output.

Sincerely yours,
Siyavash.
 

Attachments

  • PANELIZATION.rar
    237.9 KB · Views: 48

Hisham.D

Newbie level 6
Joined
Dec 21, 2012
Messages
11
Helped
6
Reputation
12
Reaction score
6
Trophy points
1,283
Activity points
1,355
You can use a gerber viewer and check the files yourself. e.g Graphicode GCPrevue which has a free version.. A quick check for your board shows that you have some unconnected nets, I can see that you have connect lines though, so you can use tools -> derive connectivity to connect the lines to the pins.
 

asadi.siyavash

Member level 4
Joined
Feb 14, 2013
Messages
68
Helped
2
Reputation
4
Reaction score
2
Trophy points
1,288
Activity points
1,769
hi Hisham,
thank you for your helpful answer, but I don't know which work I should do that I understand my file is correct.
I understood for creating a gerber file from my PCB I should create these parts, but is there any complete application note that I can use it?
1.each layer
2.solder mask layer top and bottom
3.Solder Paste Layer top and bottom
4.Silk Screen Layer top and bottom
5.Fabrication Drawing Page 1(for Ref. ONLY)
6.Fabrication Drawing Page 2)for Ref. ONLY)
7.Assembly Drawing Page 1 (for Ref. ONLY)
8.Assembly Drawing Page 2 (for Ref. ONLY)
9.Drill tape, Layer 1 through 2
10.Drill tape, Layer 1 through 3
11.Drill tape, through
12.Drill tape setup file
13.Drill tape composite file (for Reference ONLY)
14.IPC-D-356 netlist (for Checking ONLY)
15.Artwork Format File (for Ref. ONLY)
16.Placement file for Assembly (for Ref. Only)
17.Allegro Netlist (for Ref. Only)

any help would be greatly appreciated,

Sincerely yours,
Siyavash.
 

Hisham.D

Newbie level 6
Joined
Dec 21, 2012
Messages
11
Helped
6
Reputation
12
Reaction score
6
Trophy points
1,283
Activity points
1,355
If you want to know what does each part of the Gerbers do, then check this **broken link removed** it has a summary about each part of the PCB gerbers. (copper layer, solder mask, solder paste ...)

If that is not what you want then try to rephrase and I will help you. Furthermore ask your pcb house if they use ODB++ it will be easier, you will need to download the add on and export the odb++ file..
 
Last edited:

FvM

Super Moderator
Staff member
Joined
Jan 22, 2008
Messages
50,784
Helped
14,600
Reputation
29,475
Reaction score
13,680
Trophy points
1,393
Location
Bochum, Germany
Activity points
290,832
For double sided PCB, you don't need more than:

top and bottom signal
top and bottom soldermask
outline (missing from your posted files and lists)
plated nc drill
optionally non-plated nc drill

When using RS274X (as in your posted files), no format or aperture info is needed, just the mapping of file names and mm or inch info
 
Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Top