Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

how to simulation the switch cap circuit

Status
Not open for further replies.

poweric

Member level 5
Joined
Oct 29, 2006
Messages
80
Helped
3
Reputation
6
Reaction score
0
Trophy points
1,286
Activity points
1,733
switch cap circuits

i want to know how to simulation the switch cap circuit while using Hspice
becasuse the CLK signal is the .tran (pulse)
i want to get the freq response of the VOUT vs VIN
thank you for help
 

jerryzhao

Full Member level 3
Joined
Oct 8, 2005
Messages
165
Helped
24
Reputation
48
Reaction score
4
Trophy points
1,298
Activity points
2,365
switchcap cadence simulation

It are two state when the switch on and off.
you can do frequency response analyse two times. one at on state and one at off state.
 

    poweric

    Points: 2
    Helpful Answer Positive Rating

shineqi

Member level 1
Joined
Jan 16, 2007
Messages
36
Helped
1
Reputation
2
Reaction score
0
Trophy points
1,286
Activity points
1,508
switch cap circuit simulation

MOS Pair or just NMOS?
 

poweric

Member level 5
Joined
Oct 29, 2006
Messages
80
Helped
3
Reputation
6
Reaction score
0
Trophy points
1,286
Activity points
1,733
switch cap simulator

the swithch is NMOS



Added after 3 minutes:

jerryzhao said:
It are two state when the switch on and off.
you can do frequency response analyse two times. one at on state and one at off state.
while i get the apart results
how do i get the totle resluts
can you give more detail?
 

jerryzhao

Full Member level 3
Joined
Oct 8, 2005
Messages
165
Helped
24
Reputation
48
Reaction score
4
Trophy points
1,298
Activity points
2,365
switch cap simulation

The totle result is you analyse two part.
The two state are two circuits. analyse the 2 state's bandwith and gain etc.
The total result that in your mean only get in .tran simulate in normal sc circuit(only for sample and hold). If you are designing SC-filter, you must do Z transfer, and use matlab do frequency analyse.
 

stocol

Newbie level 6
Joined
Oct 24, 2007
Messages
13
Helped
1
Reputation
2
Reaction score
0
Trophy points
1,281
Activity points
1,353
if u make your simulation in spectre of cadence, u can choose PSS+PAC to simulate the frequency response of SC circuits
hope it helps
 

    poweric

    Points: 2
    Helpful Answer Positive Rating

ynhe

Full Member level 3
Joined
May 28, 2001
Messages
184
Helped
6
Reputation
12
Reaction score
2
Trophy points
1,298
Location
China
Activity points
1,344
You could use Simplis.

B/R

ynhe
 

    poweric

    Points: 2
    Helpful Answer Positive Rating

poweric

Member level 5
Joined
Oct 29, 2006
Messages
80
Helped
3
Reputation
6
Reaction score
0
Trophy points
1,286
Activity points
1,733
ynhe said:
You could use Simplis.

B/R

ynhe
what is
the "simplis " B/R
is it a tool for this ? can you explain more detail thank you
 

ynhe

Full Member level 3
Joined
May 28, 2001
Messages
184
Helped
6
Reputation
12
Reaction score
2
Trophy points
1,298
Location
China
Activity points
1,344
Hi:
SIMPLIS (SIMulation for Piecewise-LInear System) is a computer software package specifically designed for the simulation and analysis of switching power supplies.
SIMPLIS has a small-signal frequency-domain analyzer specifically designed for
the analysis of switching piecewise-linear systems. The analysis is based on the timedomain simulation of the switching piecewise-linear systems without having to resort to any circuit averaging or derivation of equivalent non-switching models.

see https://www.catena.uk.com for details.

ynhe
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Top