+ Post New Thread
Results 1 to 8 of 8
  1. #1
    Newbie level 5
    Points: 600, Level: 5

    Join Date
    Feb 2015
    Posts
    10
    Helped
    0 / 0
    Points
    600
    Level
    5

    why Phase detector IC input pin reading is always the same?

    Hello every one,
    I am software guy, don't have much idea about RF design.
    These days, I am trying to experiment on phase detector IC(AD8302). As attached figure, while trying to measure an input values at pin INPA and INPB, it always reads 4.85V. This reading is the same whether there is RF power or not. Actually, the output reading is correct as compare to phase shift on Oscilloscope. An input limitation(maximum) at those to pins is 13dbV(0.22V) as it is described on the datasheet. Even that was why I added the voltage divider on the input side as shown in the figure. My doubt here is that, why the reading is always 4.85V and would it be safe? can input at pin INPA and INPB exceeds 13dbV(0.22V) ?

    I would like to thank all in advance.
    Click image for larger version. 

Name:	fig1.png 
Views:	7 
Size:	55.4 KB 
ID:	144554

    •   Alt14th February 2018, 01:37

      advertising

        
       

  2. #2
    Super Moderator
    Points: 54,820, Level: 57
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    11,098
    Helped
    2603 / 2603
    Points
    54,820
    Level
    57

    Re: why Phase detector IC input pin reading is always the same?

    Hi,

    "Pin reading". What measurement device? What value us shown?
    * "average" is just the DC offset, it may be the same value with or without RF
    * "RMS" value can be with and without DC.

    I'm not familiar with this application...but the IC is called "phase detector". It may operate similar to a logic "XOR" circuit.
    Then the RF input signal may be constant, but with varying phase shift, the output signal will vary.

    Best is you read the IC datasheet ... or go to the manufacturer's internet pages, and look for relating application notes to get more detailed informations about it's operation.

    Klaus
    Please dont contact me via PM, because there is no time to respond to them. Thank you.



  3. #3
    Newbie level 5
    Points: 600, Level: 5

    Join Date
    Feb 2015
    Posts
    10
    Helped
    0 / 0
    Points
    600
    Level
    5

    Re: why Phase detector IC input pin reading is always the same?

    Quote Originally Posted by KlausST View Post
    Hi,

    "Pin reading". What measurement device? What value us shown?
    * "average" is just the DC offset, it may be the same value with or without RF
    * "RMS" value can be with and without DC.

    I'm not familiar with this application...but the IC is called "phase detector". It may operate similar to a logic "XOR" circuit.
    Then the RF input signal may be constant, but with varying phase shift, the output signal will vary.

    Best is you read the IC datasheet ... or go to the manufacturer's internet pages, and look for relating application notes to get more detailed informations about it's operation.

    Klaus

    Dear Klaus,
    Thank you very much for your berief.
    I just used oscilloscope and Multimeter to measure RMS value at pin INPA an d INPB. It shows 4.85 volts with and without RF Power. As I have understood from the datasheet, an input maximum is limited to 0.22V. But here it is 4.85V. On the other hand, it is the same(4.85V)all the time.

    Thank you once again



    •   Alt14th February 2018, 04:43

      advertising

        
       

  4. #4
    Full Member level 5
    Points: 3,925, Level: 14

    Join Date
    May 2006
    Posts
    247
    Helped
    86 / 86
    Points
    3,925
    Level
    14

    Re: why Phase detector IC input pin reading is always the same?

    It is the DC bias on the input pin, look at Circuit A on page 5 of the data sheet you will see that the voltage on the two pins is about 100mV less than the supply.
    The maximum input referred to is the maximum signal the device can handle, the difference between INPA and OFSA.
    Peter



  5. #5
    Advanced Member level 5
    Points: 25,907, Level: 39

    Join Date
    Nov 2001
    Location
    Earth
    Posts
    3,659
    Helped
    1120 / 1120
    Points
    25,907
    Level
    39

    Re: why Phase detector IC input pin reading is always the same?

    It's internal DC bias voltage, not RF signal strength.
    The RF signal level should be measured with an Spectrum Analyzer with a high impedance probe to avoid the performance degradation.
    A high impedance probe can also be used with a high quality oscilloscope.



  6. #6
    Super Moderator
    Points: 54,820, Level: 57
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    11,098
    Helped
    2603 / 2603
    Points
    54,820
    Level
    57

    Re: why Phase detector IC input pin reading is always the same?

    Hi,

    A measurement is only as good as the knowledgement of how and what to measure.

    If you want to measure the RF signal voltage, that is biased with DC voltage..
    * you can't use "average" method
    * you can't use "RMS including DC" method
    --> you need to use "RMS excluding DC" method.

    If your measurement tool can't exclude DC, then a simple RC high pass filter will do this.

    Klaus
    Please dont contact me via PM, because there is no time to respond to them. Thank you.



  7. #7
    Newbie level 5
    Points: 600, Level: 5

    Join Date
    Feb 2015
    Posts
    10
    Helped
    0 / 0
    Points
    600
    Level
    5

    Re: why Phase detector IC input pin reading is always the same?

    Quote Originally Posted by KlausST View Post
    Hi,

    A measurement is only as good as the knowledgement of how and what to measure.

    If you want to measure the RF signal voltage, that is biased with DC voltage..
    * you can't use "average" method
    * you can't use "RMS including DC" method
    --> you need to use "RMS excluding DC" method.

    If your measurement tool can't exclude DC, then a simple RC high pass filter will do this.

    Klaus
    Klaus,

    Thank you a lot.
    I will try to measure accordingly



    •   Alt16th February 2018, 12:34

      advertising

        
       

  8. #8
    Advanced Member level 5
    Points: 32,282, Level: 43

    Join Date
    Oct 2001
    Posts
    4,622
    Helped
    1351 / 1351
    Points
    32,282
    Level
    43

    Re: why Phase detector IC input pin reading is always the same?

    As already stated, in that point you should measure the power with a high impedance SA probe.
    Any voltage measurements in that point are pretty useless.
    The AD8302 datasheet mention very clear that the input power range is between -60dBm to 0dBm.



--[[ ]]--