+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Full Member level 3
    Points: 4,199, Level: 15

    Join Date
    Mar 2002
    Posts
    185
    Helped
    0 / 0
    Points
    4,199
    Level
    15

    How to synthesize lumped model from s-param of inductor?

    Which software can most conveniently do this and small?

    the flow is generate touchstone file from HFSS, and then translate it into lumped model.

    thanks,

    •   AltAdvertisment

        
       

  2. #2
    Junior Member level 3
    Points: 1,536, Level: 8

    Join Date
    Sep 2005
    Posts
    29
    Helped
    1 / 1
    Points
    1,536
    Level
    8

    How to synthesize lumped model from s-param of inductor?

    this is a huge area of research... which often leads to a phd work
    so you would not find any easy to use software.

    you may like to search inductor modelling on IEEE



    •   AltAdvertisment

        
       

  3. #3
    Newbie level 5
    Points: 1,338, Level: 8

    Join Date
    Feb 2007
    Posts
    10
    Helped
    4 / 4
    Points
    1,338
    Level
    8

    How to synthesize lumped model from s-param of inductor?

    CST MWS has can extract spice model from the S parameters

    You can also try EMtoSPICE from http://www.emwonder.com/



    •   AltAdvertisment

        
       

  4. #4
    Advanced Member level 3
    Points: 10,596, Level: 24

    Join Date
    Aug 2005
    Location
    INDIA
    Posts
    810
    Helped
    239 / 239
    Points
    10,596
    Level
    24

    Re: How to synthesize lumped model from s-param of inductor?

    Hello,


    Sonnet Software has this capability...
    Which generates Broadband Spice model from S-Parameters...
    http://www.sonnetsoftware.com/
    http://www.sonnetsoftware.com/produc...e/download.asp


    ---manju---



  5. #5
    Newbie level 5
    Points: 1,281, Level: 8

    Join Date
    Feb 2006
    Posts
    10
    Helped
    1 / 1
    Points
    1,281
    Level
    8

    Re: How to synthesize lumped model from s-param of inductor?

    Not sure if S Parameter data alone is sufficient to fit curves. I think one needs more measured data like ESR.. Check out the MTT; I can look something up, if you want.



    •   AltAdvertisment

        
       

  6. #6
    Advanced Member level 3
    Points: 9,181, Level: 22

    Join Date
    Sep 2003
    Posts
    868
    Helped
    176 / 176
    Points
    9,181
    Level
    22

    Re: How to synthesize lumped model from s-param of inductor?

    Hi:

    There are quite some tools can convert s-parameters into RLC or SPICE netlist in a wide frequency band. However, none of them can guarantee the RLC are always positive or the SPICE netlist to be of passive components only. It seems impossible to avoid negative RLC or active devices inside the SPICE net list. If possible, I do suggest people try to perform time transient analysis directly from s-parameters without converting them to RLC or control sources. It should avoid the problems involved in negative RLC or control sources in the SPICE netlist. The MDSPICE from ZELAND can perform time transient analysis directly from s-parameters and it can also convert s-parameters into RLC with perfect matching in a wide frequency range. I am from Zeland. Regards.



--[[ ]]--