Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

lmhostid command returns nothing .. HELP

Status
Not open for further replies.
E

eda_wiz

Advanced Member level 2
Joined
Nov 7, 2001
Messages
653
Helped
58
Reputation
116
Reaction score
29
Trophy points
1,308
Activity points
6,195
lmhostid

Hi all,
./lmhostid in linux returns me ""

I dont have a ethernet card in my pc .. how will i know my hostid sothat i can gen my lic. Or can i generate lic with diskserialno or flexid for linux

tnx
 

lmhostid linux

I got the same issue using VMware!
 

lmhostid vmware

If you type in xterm "lmhostid" , this will return back with HostID of your computer.
 

linux lmhostid

The problem is that this is the answer from lmhostid : hostid=""
 

vmware lmhostid empty

You need a Ethernet Card or Dongle in printer port for lmhostid. The default IP is 127.0.0.1. Try this one if you don't have Ethernet Card.
 

lmhostid returns nothing

I would like to refocus this threat as I am have this problem when installing Cadence on Suse 10 within Vmware. So just wondering if anyone has found the answer the problem earlier.
 

lmhostid empty

what does /sbin/ifconfig tell you?
 

command to get lmhostid

linux:~ # ifconfig
eth2 Link encap:Ethernet HWaddr 00:0C:29:26:FA:D8
inet addr:192.168.1.68 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe26:fad8/64 Scope:Link
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:408 errors:0 dropped:0 overruns:0 frame:0
TX packets:200 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:47794 (46.6 Kb) TX bytes:16584 (16.1 Kb)
Interrupt:10 Base address:0x1400

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:26 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1644 (1.6 Kb) TX bytes:1644 (1.6 Kb)
Click to expand...

The above is the message returned from ifconfig, the HW address which is what the lmhostid is suppposed to return is present so I not understand why would it be empty.
 

lmutil lmhostid return null

Maybe you can get more information using the lmutil command.
 

lmhostid returns null centos

Hi
try hostid=any
regards
 
  • Like
Reactions: hargu

    H

    hargu

    Points: 2
    Helpful Answer Positive Rating
lmutil lmhostid return null

That only works with some license schemes.
 

lmutil lmhostid dont return

run the given make file, then navigate to that folder after that run the command.
as u dont have ethernet card u've default IP. but many licences are based on such ids only as they are necssary component of system.hard disk number is also one of them.
 

suse lmhostid

DISK_SERIAL_NO Was abandoned many years ago, but it's worth a try - what is puzzling is the command should return all valid hardware HOSTID's - or since it's been years since I worked on Unix, (equiv. Linux), does the command return the HOSTID in the lic. file? - if so it could be port@xxxx - if the network is unavailable then you might get a null string.

SiGiNT
 

lmhostid en linux

The problem is that I have a sort of have an ethernet card. I am actually running the suse 10.3 on Vmware Workstation 5.0.
 

empty lmhostid

Why not check your vmware,so that it will show you a vmnet card?
Create a new virtual machine with bridge mode,I remember that the vmware also have hardware address.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top