+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Junior Member level 3
    Points: 983, Level: 7

    Join Date
    Feb 2015
    Posts
    25
    Helped
    0 / 0
    Points
    983
    Level
    7

    Using AD831 in parallel

    Hello every one,

    I am software guy. Some how trying to use ad831 as a mixer connecting in parallel as seen on attached file. +5V and -5V are supplied to both of the mixers from the same source. The problem I faced is here. While measuring the supplied -5V at each mixer it shows ~ -1.2V. what could be the problem?
    Click image for larger version. 

Name:	ad831.PNG 
Views:	5 
Size:	47.9 KB 
ID:	156041

    •   AltAdvertisement

        
       

  2. #2
    Super Moderator
    Points: 78,412, Level: 68
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    15,910
    Helped
    3609 / 3609
    Points
    78,412
    Level
    68

    Re: Using AD831 in parallel

    Hi,

    * bad DVM
    * bad -5V power supply
    * too high current

    Klaus
    Please donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



    •   AltAdvertisement

        
       

  3. #3
    Junior Member level 3
    Points: 983, Level: 7

    Join Date
    Feb 2015
    Posts
    25
    Helped
    0 / 0
    Points
    983
    Level
    7

    Re: Using AD831 in parallel

    Quote Originally Posted by KlausST View Post
    Hi,

    * bad DVM
    * bad -5V power supply
    * too high current

    Klaus

    Dear Klaus,

    Thank you very much for your help.

    I have been using my digital multimeter(DVM) for some other circuit and working properly. The -5V supply source is also working perfectly while applying for other circuits. As you mentioned, there is high current measured. That could be a problem. how I may resolve that one?

    Thank you once again.



    •   AltAdvertisement

        
       

  4. #4
    Super Moderator
    Points: 78,412, Level: 68
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    15,910
    Helped
    3609 / 3609
    Points
    78,412
    Level
    68

    Re: Using AD831 in parallel

    Hi,

    First you need to determine:
    * How much current can your supply deliver
    * How much current do you expect your circuit to draw
    * Measure how much your circuit really draws

    We don't know how to debug your circuit, because you didn't show.
    Are the ICs socketed? Breadboard, PCB, is something getting hot....do you have coolant spray? Soldering skills...

    Btw: some brand (negative) voltage regulators suffer from not properly starting up when negative voltage is applied.
    In one application we also had +5V and -5V regulators, but the negative did not start up because the positive was faster..causing some positive glitch at the negative VR's output. This was a cheap 7905 .... we solved this problem by using a high quality brand VR.

    Klaus
    Please donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



  5. #5
    Junior Member level 3
    Points: 983, Level: 7

    Join Date
    Feb 2015
    Posts
    25
    Helped
    0 / 0
    Points
    983
    Level
    7

    Re: Using AD831 in parallel

    Quote Originally Posted by KlausST View Post
    Hi,

    First you need to determine:
    * How much current can your supply deliver
    * How much current do you expect your circuit to draw
    * Measure how much your circuit really draws

    We don't know how to debug your circuit, because you didn't show.
    Are the ICs socketed? Breadboard, PCB, is something getting hot....do you have coolant spray? Soldering skills...

    Btw: some brand (negative) voltage regulators suffer from not properly starting up when negative voltage is applied.
    In one application we also had +5V and -5V regulators, but the negative did not start up because the positive was faster..causing some positive glitch at the negative VR's output. This was a cheap 7905 .... we solved this problem by using a high quality brand VR.

    Klaus
    Dear Klaus,

    The -5V voltage regulator I am using is NJM7905A which can supply up to 1A. I expect my circuit to draw around 0.65A approximately. But, what it actually draws is 1.2A. The PCB is getting very hot for which I disn't use coolant spray. I will try to use standard VR as you suggested. would you suggest me one to use?

    If you have any more suggestions depend on the information I am writing now, I would love to say thank you in advance.


    Thank you a lot.



    •   AltAdvertisement

        
       

  6. #6
    Super Moderator
    Points: 78,412, Level: 68
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    15,910
    Helped
    3609 / 3609
    Points
    78,412
    Level
    68

    Re: Using AD831 in parallel

    Hi,

    The PCB is getting very hot for which I disn't use coolant spray.
    I doubt the PCB is getting hot. Usually the electronic parts getting hot. .. and only some of them.

    To detect which one is getting hot:
    * power off and let all get down to room temperature
    * use coolant spray in a way that everything gets white / icy surface.
    * then switch power ON and watch the parts which ones first melt the icy surface.

    Klaus
    Please donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



--[[ ]]--