+ Post New Thread
Results 1 to 9 of 9

31st August 2019, 23:29 #1
 Join Date
 Jan 2018
 Posts
 202
 Helped
 1 / 1
 Points
 1,228
 Level
 7
How do you choose input power while doing loadpull?
Hi, usually we would like to know what is the output power(Pout1dB) at input 1 dB compression point (Pin1dB). Does this mean first I find Pin1dB and then do the loadpull at this input power? Basically how do I choose how much input power I should provide? Thanks

Advertisement

31st August 2019, 23:50 #2
 Join Date
 Nov 2001
 Location
 Turkey
 Posts
 4,458
 Helped
 1340 / 1340
 Points
 30,417
 Level
 42
Re: How do you choose input power while doing loadpull?
Yes, you should apply P1dB(in) to do loadpull..Because this point where the nonlinearity starts to become dominant on the amplifier's performance so it's a kind of threshold..
1 members found this post helpful.

2nd September 2019, 12:45 #3
 Join Date
 Jan 2018
 Posts
 202
 Helped
 1 / 1
 Points
 1,228
 Level
 7

Advertisement

3rd September 2019, 00:57 #4

Advertisement

3rd September 2019, 14:35 #5
 Join Date
 Jan 2019
 Location
 Belgium
 Posts
 199
 Helped
 83 / 83
 Points
 1,400
 Level
 8
Re: How do you choose input power while doing loadpull?
Why not put in the frequency everywhere as a variable and do a parametric sweep of that variable.

3rd September 2019, 23:59 #6
 Join Date
 Jan 2018
 Posts
 202
 Helped
 1 / 1
 Points
 1,228
 Level
 7
Re: How do you choose input power while doing loadpull?
I didn't understand much whenever you mentioned about SKILL scripting language. Now it started making sense to me, I should learn this.
   Updated   
Yes I was doing that, I could get all the Pin1dB points. But now I need to figure out how to run another simulation for loadpull at different frequencies using their respective pin1dB points.
Code:analysis('hb parameter Pin ) paramAnalysis("frequency") paramRun() save Pin1dB points ..I don't know what to do here analysis('hb Parameter mag and theta ) Use the saved Pin1dB points paramAnalysis("frequency") paramRun()
Last edited by circuitking; 4th September 2019 at 00:19.

19th September 2019, 10:13 #7
 Join Date
 Sep 2019
 Location
 nepal
 Posts
 10
 Helped
 2 / 2
 Points
 78
 Level
 1
Re: How do you choose input power while doing loadpull?
Although most RF systems are designed for nominal 50ohm input and output ... Further, the power levels in 4G wireless systems and upcoming 5G ... Q: What's the general procedure for making load pull tests and using the results? ... a dozen among which to choose) with suitable application support in ...

26th September 2019, 00:56 #8
 Join Date
 Jan 2018
 Posts
 202
 Helped
 1 / 1
 Points
 1,228
 Level
 7
Re: How do you choose input power while doing loadpull?
After reading this post https://www.edaboard.com/showthread....plifierDesign, it makes me think.
What is the pout that is shown at optimum load , Is it p1dB(out) or maximum power (Psat). As Vivekroy mentioned in that post loadpull gives maximum power for that particular optimum load. Then what is the point in giving P1dB(in) to do loadpull?

Advertisement

26th September 2019, 03:52 #9
 Join Date
 Jan 2019
 Location
 Belgium
 Posts
 199
 Helped
 83 / 83
 Points
 1,400
 Level
 8
Re: How do you choose input power while doing loadpull?
The pout for optimum load is the pout you would get if you connected the optimum load (from loadpull simulation) and put in the input power at which you did the loadpull.
It is not necessary to give P1dB for loadpull. For example, for constant envelope waveforms (eg. FM), you give input power corresponding to the point where you get maximum efficiency which can be far from P1dB.
+ Post New Thread
Please login