+ Post New Thread
Results 1 to 8 of 8

28th August 2019, 04:48 #1
 Join Date
 Aug 2018
 Posts
 61
 Helped
 0 / 0
 Points
 489
 Level
 4
Zero crossing detecting formula 3 phase network
Dear all.
I am looking for the simple 3 phase zero crossing ckt and its formula to calculating it. I am trying with arduino uno board. Kindly suggest any recommended CKt

Advertisement

28th August 2019, 05:06 #2
 Join Date
 Nov 2012
 Posts
 3,149
 Helped
 777 / 777
 Points
 17,237
 Level
 31
Re: Zero crossing detecting formula 3 phase network
I am looking for the simple 3 phase zero crossing ckt...
For simplicity, you can use simple diode logic AND /OR gates. You should also limit the final pulses with a voltage limiter (say with a zener diode).

Advertisement

28th August 2019, 05:36 #3
 Join Date
 Aug 2015
 Posts
 1,815
 Helped
 674 / 674
 Points
 11,189
 Level
 25
Re: Zero crossing detecting formula 3 phase network
You need to identify whether you need to detect the zero crossing relative to neutral point  or between each pair of two phases  these are different points and phase shifted in time.

Advertisement

28th August 2019, 05:58 #4
 Join Date
 Aug 2018
 Posts
 61
 Helped
 0 / 0
 Points
 489
 Level
 4
Re: Zero crossing detecting formula 3 phase network
i wanted to measure degree phase shift. I wanted calculation for my application like this
i have 3 phase 4 wire system. looking for equations
Line to Line and Line to Neutral voltage.when R,Y,B are independently connected.
Now assume that i have tapped R to common point Yphase and Bphase. During this condition there will be no phase shift since i have used single phase line. Then how calculations are taken into consideration.
Line to line and line to neutral .
i thought zero crossing ckt and equation might solve this. Is there any example ckts and equation that i can tested out with MCU.

28th August 2019, 06:50 #5
Awards:
 Join Date
 Apr 2014
 Posts
 15,774
 Helped
 3592 / 3592
 Points
 77,851
 Level
 68
Re: Zero crossing detecting formula 3 phase network
Hi,
To be able to calculate the phase shift you need the zero cross of voltage as well as zero cross of current.
Please consider:
If you have symmetric load you need just one pair. Otherwise you need a pair for each phase.
Please know that: cos(phi) = power_factor is only true for purly sinusoidal waveforms.
For varying currents (sometimes small, sometimes high) it's very difficult to get a precise zero cross signal.
Also note that overtones or other noise in voltage and current will cause the phase shift to jitter causing faulty results.
Thus: if you have varying currents and/or overtones in current, then I recommend to use 4 (1 x V, 3 x I) ADC channels to measure and calculate V_RMS, I_RMS, phase shift, true_power, power_factor .... precisely.
If done precisiin measurements many times. If you want precision your task becomes really difficult.
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

28th August 2019, 08:37 #6
Awards:
 Join Date
 Jul 2009
 Location
 Aberdyfi, West Wales, UK
 Posts
 13,349
 Helped
 4456 / 4456
 Points
 81,434
 Level
 69
Re: Zero crossing detecting formula 3 phase network
Also be aware that simply using a voltage divider to drop the phase voltages will not in itself make it measurable or even zero crossing detectable if fed to an MCU. You at the very least need to cater for the reversal of polarity and some over voltage protection would be a worthwhile addition.
There is no definitive reference to the phase timings, you have to measure one relative to the other two. As Klaus stated, ideally you need three voltage detectors and three current detectors. The voltage zero crossings will tell you the angle between the phase wires and the current zero crossing relative to those will give you the load phase shift.
Brian.PLEASE  no friends requests or private emails, I simply don't have time to reply to them all.
It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.

28th August 2019, 16:13 #7
Re: Zero crossing detecting formula 3 phase network
Lastly....
Those capacitors, C1, C2, C3 will generate a phase shift on the voltage samples.
As shown in the simulation, it will be about 7.5 degrees at 60 Hz. This can be significant, depending on what you want to measure.Last edited by schmitt trigger; 28th August 2019 at 16:29.
My batteries are recharged by "Helpful Post" ratings.
If you feel that I've helped you, please indicate it as a Helpful Post

Advertisement

29th August 2019, 13:22 #8
 Join Date
 Apr 2011
 Location
 Minneapolis, Minnesota, USA
 Posts
 12,949
 Helped
 2580 / 2580
 Points
 52,942
 Level
 56
Re: Zero crossing detecting formula 3 phase network
A pair of antiparallel led's makes a handy method to indicate volt level and polarity. Or optoisolators.
Another pair of led's (optoisolators) can indicate current, if it's low enough to be safe for led's. Or else to indicate high current, place a shunt in parallel with the pair, but then it has to develop sufficient voltage so that led's turn on.
All photodetectors are in a separate circuit together with a low voltage power supply and your Arduino. It's isolated from high voltage, and it easily reads 3phase behavior, positive and negative polarities, star and delta. It allows easy interpretation of phase differences between voltage and current waveforms.
+ Post New Thread
Please login