+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Full Member level 1
    Points: 1,069, Level: 7

    Join Date
    Mar 2017
    Posts
    106
    Helped
    0 / 0
    Points
    1,069
    Level
    7

    Power Amplifier Design

    For load-pull simulation to extract optimum load impedance. How to set input power ? According to what?

    Thanks in advanced

    •   AltAdvertisement

        
       

  2. #2
    Advanced Member level 5
    Points: 31,239, Level: 43
    BigBoss's Avatar
    Join Date
    Nov 2001
    Location
    Turkey
    Posts
    4,588
    Helped
    1384 / 1384
    Points
    31,239
    Level
    43

    Re: Power Amplifier Design

    Output Power should be vicinity of P1dB. In fact, there isn't any convention about that because some manufacturers use P3dB some of them P1dB.
    Nevertheless, P1dB Compression Point is chosen and Input Power is adjusted in according with that.Because Optimum Load will be used to achieve max. [specification]
    [specification]: max Pdelivered or max. Efficiency or max. Power Gain..


    1 members found this post helpful.

    •   AltAdvertisement

        
       

  3. #3
    Full Member level 1
    Points: 1,069, Level: 7

    Join Date
    Mar 2017
    Posts
    106
    Helped
    0 / 0
    Points
    1,069
    Level
    7

    Re: Power Amplifier Design

    Quote Originally Posted by BigBoss View Post
    Output Power should be vicinity of P1dB. In fact, there isn't any convention about that because some manufacturers use P3dB some of them P1dB.
    Nevertheless, P1dB Compression Point is chosen and Input Power is adjusted in according with that.Because Optimum Load will be used to achieve max. [specification]
    [specification]: max Pdelivered or max. Efficiency or max. Power Gain..
    Thanks for the valuable information. Is the same thing is considered for doherty sub-amplifiers (main & auxiliary)? I want to do a correct DPA design, but still confusing about load pull setting such as input power level for each one of the sub-amplifiers



    •   AltAdvertisement

        
       

  4. #4
    Advanced Member level 5
    Points: 54,214, Level: 56
    Achievements:
    7 years registered
    Audioguru's Avatar
    Join Date
    Jan 2008
    Location
    Toronto area of Canada
    Posts
    8,838
    Helped
    2072 / 2072
    Points
    54,214
    Level
    56

    Re: Power Amplifier Design

    When you said Power Amplifier Design I thought it would drive an 8 ohms speaker.



  5. #5
    Advanced Member level 5
    Points: 31,239, Level: 43
    BigBoss's Avatar
    Join Date
    Nov 2001
    Location
    Turkey
    Posts
    4,588
    Helped
    1384 / 1384
    Points
    31,239
    Level
    43

    Re: Power Amplifier Design

    Quote Originally Posted by Mabrok View Post
    Thanks for the valuable information. Is the same thing is considered for doherty sub-amplifiers (main & auxiliary)? I want to do a correct DPA design, but still confusing about load pull setting such as input power level for each one of the sub-amplifiers
    You should drive the PA until the PA enters into SAT mode in order to observe the Efficiency in Main and Aux. Amplifier regions. Back-Off effect in Efficiency can be observed with this method ..



    •   AltAdvertisement

        
       

  6. #6
    Full Member level 4
    Points: 1,626, Level: 9

    Join Date
    Jan 2019
    Location
    Ireland
    Posts
    223
    Helped
    94 / 94
    Points
    1,626
    Level
    9

    Re: Power Amplifier Design

    I do loadpull for the main amplifier at two points:
    1. Just before the peaking amplifier turns on and begins to significantly do "load modulation".
    2. When both the amplifiers are saturated.
    For the peaking amplifier, I do loadpull at the peak point where both the amplifiers are saturated.


    1 members found this post helpful.

--[[ ]]--