+ Post New Thread
Results 1 to 7 of 7

13th August 2019, 17:21 #1
 Join Date
 Apr 2014
 Location
 Belgium
 Posts
 87
 Helped
 0 / 0
 Points
 1,414
 Level
 8
Calculating switching losses of a mosfet when switching energy is not given
Hi,
The title pretty much says it all. I’m not sure what factors these losses are based on. I saw somewhere you need to multiply the sum of the rise and fall time by the drainsource voltage and current, but I don’t think the losses are this high.
Thanks

Advertisement

13th August 2019, 21:38 #2
Awards:
 Join Date
 Apr 2014
 Posts
 15,461
 Helped
 3515 / 3515
 Points
 76,249
 Level
 67
Re: Calculating switching losses of a mosfet when switching energy is not given
Hi,
It depends what values you use
P(t) = V(t) × I(t)
But P(avg) is not V(avg) × I(avg)
And P(RMS) is not V(RMS) × I(RMS)
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

13th August 2019, 22:05 #3
 Join Date
 Apr 2014
 Location
 Belgium
 Posts
 87
 Helped
 0 / 0
 Points
 1,414
 Level
 8
Re: Calculating switching losses of a mosfet when switching energy is not given
Thanks for your reply.
I don’t really understand what you’re saying. Could you please elaborate or maybe give an example for this mosfet at say 500V and 10A drainsource driven by a 1kHz square wave?

Advertisement

14th August 2019, 01:53 #4
Awards:
 Join Date
 Apr 2014
 Posts
 15,461
 Helped
 3515 / 3515
 Points
 76,249
 Level
 67
Re: Calculating switching losses of a mosfet when switching energy is not given
Hi,
Let's say you have a Mosfet with 50% duty cycle, average drain current of 10A and average drainsource voltage of 10V.
Then the power dissipation may be from about zero (let's say 0.1W) up to 100W.
It depends on at which time which voltage and which current is.
It's not (only) a question of the used Mosfet.
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.
1 members found this post helpful.

14th August 2019, 02:19 #5
 Join Date
 Aug 2015
 Posts
 1,636
 Helped
 590 / 590
 Points
 9,987
 Level
 23
Re: Calculating switching losses of a mosfet when switching energy is not given
typically in a circuit with an inductive load, the current must rise to full value before the volts across the device turning on can fall  so turn on losses are Vbus x 0.5 Iload x time to turn ON x freq = losses, assuming the current ramps up linearly. For resistive load losses = 0.5 times prev example as we assume the volts fall linearly at turn on.
Very similar for turn off losses for turning off an inductive load the volts go up quickly & stay high as the current goes from full to zero > same formula losses = 0.5 x Vbus x Iload x time to turn off x freq.
ditto for resistive load turn off as turn on, for losses, as the V & I cross over linearly, 0.25 x V x I x Toff time x freq.
hope this helps
1 members found this post helpful.

Advertisement

14th August 2019, 09:47 #6
 Join Date
 Apr 2014
 Location
 Belgium
 Posts
 87
 Helped
 0 / 0
 Points
 1,414
 Level
 8
Re: Calculating switching losses of a mosfet when switching energy is not given
Thanks for your replies.
I guess what it comes down to is that it's quite hard to calculate switching losses as they depend on a lot of factors, and that the calculations from my first post are about twice as high as a typical worst case scenario because they assume max voltage and current throughout the whole switching process instead of a (still not accurate) linear increase or decrease.
I've been playing with LTspice for a bit and I think those calculations are the most accurate I'm going to get, given a good model.

14th August 2019, 19:40 #7
Awards:
 Join Date
 Apr 2014
 Posts
 15,461
 Helped
 3515 / 3515
 Points
 76,249
 Level
 67
Re: Calculating switching losses of a mosfet when switching energy is not given
Hi,
As with many electronics topics:
MOSFET manufacturers provide application notes how to calculate this.
Those application notes from big semiconductor manufacturers are for free, reliable and usually good explained.
> use them.
Easy to find:
https://lmgtfy.com/?q=application+no...er+dissipation
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.
+ Post New Thread
Please login