+ Post New Thread
Results 1 to 6 of 6

4th August 2019, 14:10 #1
 Join Date
 Oct 2006
 Location
 Real Homeless
 Posts
 2,628
 Helped
 708 / 708
 Points
 17,097
 Level
 31
Correction of Frequency in Arrival Direction Detection
Carrier frequency of receiving signal is same as local frequency of receiver for rader system, if we ignore doppler shift.
In this case, we can evaluate arrival direction by using https://www.edaboard.com/showthread....eering%20music
However if a target generates own carrier which is slightly different from local frequecy of receiver, I don't think we can apply above algorithm directly.
Here I have to correct frequency difference.
Am I correct ?

Advertisement

6th August 2019, 04:01 #2
 Join Date
 Oct 2017
 Posts
 151
 Helped
 23 / 23
 Points
 1,113
 Level
 7
Re: Correction of Frequency in Arrival Direction Detection
I think correction is not required for angular information. For phase monopulse receiver both antennas will receive same transmitter frequency, DOA may be extracted using simple FFT (which may be replaced by MUSIC)
For example:
receiver frequency F
transmitter frequency F+1MHz
antenna 1 mixer output > ADC > FFT > found peak at 1MHz, phase phi1
antenna 2 mixer output > ADC > FFT > found peak at 1MHz, phase phi2
finding DOA: (phi2phi1)*k depending on antenna spacing, angle will be mirrored if transmitter frequency is Ftr = F  1MHz
Or you meant some other case?
Maybe this will interest you, something about correction:
https://www.semanticscholar.org/pape...d9d88e06dbca6f

Advertisement

6th August 2019, 04:42 #3
 Join Date
 Oct 2006
 Location
 Real Homeless
 Posts
 2,628
 Helped
 708 / 708
 Points
 17,097
 Level
 31
Re: Correction of Frequency in Arrival Direction Detection
It is a frequency compensate actually, since frequency deviation of 1MHz is evaluated.
E[(ftxfrx)*time] is not zero.Last edited by pancho_hideboo; 6th August 2019 at 04:28.

Advertisement

6th August 2019, 11:26 #4

6th August 2019, 16:03 #5
 Join Date
 Sep 2007
 Location
 Richmond Hill, ON, Canada
 Posts
 6,729
 Helped
 1679 / 1679
 Points
 34,834
 Level
 45
 Blog Entries
 7
Re: Correction of Frequency in Arrival Direction Detection
One of my 1st designs was replacing ground based Radar with Doppler using OCXO +PLL to 100kHz subcarrier FM pilot tone on Tx, then received and mixed with same OCXO ( using PLL to scale to same 10MHz) to get change in RANGE and azimuth shift with 2 antenna. It worked very well since my design was stable to 1e10 for rocket harsh environment of 100g shock, 50g accel, and 15g vibe.
Range is phase of 1 cycle at speed of light and velocity is d (phi) /dt so counting cycles determines total range.
I used an analog sawtooth mixer so the result was an analog linear phase shift with range. It worked very well and the error frequency was nulled before launch. Circa 1976
The resulting out waveform was an exact duplicate of the sawtooth due to my method of precise very fast S&H such that if each transition of the sawtooth were used to accumulate instead , you would see the precise parabolic path of the rocket as perceived by the apparent tangent distance called "Range" and this can see the peak apparent altitude ( just after Apogee) and thus the mixed output sawtooth slows to a zero ramp 0 f. or DC then changes direction or slope coming down to earth. In our case Apogee was over 500 miles for plasma research.Last edited by SunnySkyguy; 6th August 2019 at 16:12.
A best design is easily achieved with good test specs™
A better question deserves a better answer. ™
... so include all your acceptance criteria ( values, % tolerance) and assumptions in your question or any design.
... Tony Stewart EE since 1975
 slightly north of Toronto

Advertisement

8th August 2019, 06:05 #6
 Join Date
 Oct 2017
 Posts
 151
 Helped
 23 / 23
 Points
 1,113
 Level
 7
Re: Correction of Frequency in Arrival Direction Detection
What is E[] ?
My current understanding is that direction may be found regardless of transmitter frequency deviation.
How is your transmitter signal is different from Doppler signal reflected from moving object?
Example:
transmitter with frequency F+F(t), F(t) unknown
receiver with LO frequency F
antenna 1: F(t) phase shift phi1
antenna 2: F(t) phase shift phi2
antenna 3: F(t) phase shift phi3
antenna 4...
DOA is found by analyzing phi1,phi2,phi3 using FFT/music/etc.
it seems that I am missing something here
+ Post New Thread
Please login