+ Post New Thread
Results 21 to 35 of 35

21st July 2019, 02:32 #21
 Join Date
 Nov 2015
 Posts
 22
 Helped
 2 / 2
 Points
 790
 Level
 6
Re: ELECTRICAL AND ELECTRONICS Instrumentation
1) I=2+4sin314t
2) 4 is the amplitude (or peak to peak) current.
3) But rms only takes the half and multiplies it by sqrt(2)/2, wich results 0.7071....
4) Then by superposition: I=2+(4/2)*.7071= 3.4142 ALast edited by flaxwalter; 21st July 2019 at 02:44.

21st July 2019, 04:57 #22
 Join Date
 Aug 2015
 Posts
 1,738
 Helped
 650 / 650
 Points
 10,751
 Level
 24
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Dear Barry, rms of A + rms of B does not give a total rms figure, rms must be added vectorially, unless they are both DC signals, or AC signals of single freq and in phase.
hence square each, add, then take the SQRT, i.e. add as vectors, rms stands for root  mean  squared, i.e. the SQRT of the mean of the squares, this is covered in 6th form mathematics and 1st year university maths, the rms current is that value that gives the same heating effect as a DC current of that value.
Dear Flaxwater, 4 is the peak ( not pkpk) superposition does not apply here, the answer is 3.46375 amps rmsLast edited by Easy peasy; 21st July 2019 at 05:14.

21st July 2019, 06:29 #23
 Join Date
 Aug 2016
 Posts
 493
 Helped
 79 / 79
 Points
 2,788
 Level
 12
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Hi Barry,
Also take a look at my LTspice simulation result of Post #13. In that simulation I added both currents as you can see in the simulation waveform and calculated the RMS value of the sum. Spice reported 3.464A which is exactly what you get by "squaring/squarerooting".
I'm looking at it as vector addition. Let's analyze the DC part as a sinusoidal representation recognising that the frequency of a DC quantity is zero, we get to see the following:
Putting Idc = 2*sin0 = 2*0 = 0A, we see that Idc is not a sine function.
Putting Idc = 2*cos0 = 2*1 = 2A, we see that Idc is a cosine function.
This means that I = 2 + 4sinx = 2cos0 + 4sinx in electricity.
I hope that's a good one.
   Updated   
Hi flaxWalter, 4 in the sine wave expression is just the peak value and not peaktopeak.
   Updated   
With this question, one thing that I have come to learn the hard way is that DC quantities are cosine functions and not sine functions. No teacher has ever told me that. Sympathetic!
Akanimo.

Advertisement

21st July 2019, 09:29 #24
 Join Date
 Jan 2008
 Location
 Bochum, Germany
 Posts
 45,259
 Helped
 13768 / 13768
 Points
 259,231
 Level
 100
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Some explanation are unnecessarily complicated, I think. The keyword is orthogonality.
Sine signals of different frequency (also freq=0, DC) are orthogonal. Their generated power adds linearly, respectively rms values have to be squared.

23rd July 2019, 14:57 #25
 Join Date
 Mar 2005
 Location
 California, USA
 Posts
 4,609
 Helped
 1020 / 1020
 Points
 24,015
 Level
 37
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Well, I guess I flunked that test...

Advertisement

23rd July 2019, 23:37 #26
 Join Date
 Aug 2016
 Posts
 493
 Helped
 79 / 79
 Points
 2,788
 Level
 12
Re: ELECTRICAL AND ELECTRONICS Instrumentation
I went a step further and I found out that it is not only frequency that determines the RMS value for such combination of waveforms. I found out that differences in phase angles between the waveforms involved play a role too. This makes SQRT(RMSA^2 + RMSB^2) not adequate for determining the RMS value in all cases. This is also the case for combinations of more than two signals.
   Updated   
This can be confirmed by simulation. I checked with LTspice.Last edited by Akanimo; 23rd July 2019 at 23:40. Reason: addition of info

Akanimo.

Advertisement

23rd July 2019, 23:59 #27
 Join Date
 Aug 2015
 Posts
 1,738
 Helped
 650 / 650
 Points
 10,751
 Level
 24
Re: ELECTRICAL AND ELECTRONICS Instrumentation
yes  it is more correct to say the vector addition of two or more uncorrelated signals
where there is a fixed phase difference  e.g. 180 degrees for an obvious case, the rms will be smaller, if the phase difference moves then the vector addition will give an average but not describe the envelope, for unrelated frequencies the vector addition still works

24th July 2019, 05:42 #28
Awards:
 Join Date
 Apr 2014
 Posts
 15,611
 Helped
 3557 / 3557
 Points
 77,053
 Level
 67
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Hi,
I went a step further and I found out that it is not only frequency that determines the RMS value
May I ask how you did your simulation?
Are you sure you did it long enough for the combined waveform to repeat (may be a lot of cycles)
You need an integer number of cycles of the one frequency a d an integer number of the other frequency.
Else you get a non integer cyle of one frequency ... where the RMS is not sqrt(2) of the peak anymore.
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

28th July 2019, 08:29 #29
 Join Date
 Aug 2016
 Posts
 493
 Helped
 79 / 79
 Points
 2,788
 Level
 12
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Actually, this was saying that differences in phase angles between combined waveforms affect the resultant RMS value.
See attached simulation result for more information.
With the same frequency, same amplitudes and at different phase angles between the two combined waveforms, the resultant RMS values turn out to be different.
   Updated   
Hence the relationship: RMS = SQRT(RMSA^2 + RMSB^2) is for waveforms that are 90 degrees out of phase with each other.
Akanimo.

28th July 2019, 09:49 #30
Awards:
 Join Date
 Apr 2014
 Posts
 15,611
 Helped
 3557 / 3557
 Points
 77,053
 Level
 67
Re: ELECTRICAL AND ELECTRONICS Instrumentation
Hi,
In post#26 .. you refer to FvM's post which clearly states "different frequency".
In post#20 ... I stated that at same frequency there is an exception..
Also in post#27 ... is mentioned "uncorrelated frequencies
And posts#24, #27, #28.....
Don't ignore all this.
For sure adding two identical frequencies result in a rotating vector of same, constant frequency and constant length..
Which is different to when you use different frequencies. (Length of vector changes with time, angular velocity is not constant).
So, your simulation is correct and does not contradict all said before.
KlausPlease don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

28th July 2019, 10:53 #31
 Join Date
 Aug 2016
 Posts
 493
 Helped
 79 / 79
 Points
 2,788
 Level
 12
Re: ELECTRICAL AND ELECTRONICS Instrumentation
I did not say that the simulation contradicts all the points made previously. I acknowledge the fact that vector addition is correct in all cases as mentioned by Easy peasy. I am just trying to strengthen the point that orthogonality is no determined by frequency but by phase. Two vectors are orthogonal when they are perpendicular and as such 90 degrees out of phase with each other.
RMS = SQRT(RMSA^2 + RMSB^2) is correct but A and B must be 90 degrees out of phase. This goes back to strengthen the point that I made earlier on with my analysis that showed that DC signals are actually cosine functions.
If we look at it, we would see that at any time t the orthogonality can be shown by: Idc + Iac_m*sin(2*pi*f*t) = Idc_m*cos(2*pi*0*t) + Iac_m*sin(2*pi*f*t) = Idc_m*cos(2*pi*0*t) + Iac_m*cos((2*pi*f*t)  90deg) = Idc_m*sin((2*pi*0*t) + 90deg) + Iac_m*sin(2*pi*f*t).
Akanimo.

28th July 2019, 13:41 #32
 Join Date
 Jan 2008
 Location
 Bochum, Germany
 Posts
 45,259
 Helped
 13768 / 13768
 Points
 259,231
 Level
 100
Re: ELECTRICAL AND ELECTRONICS Instrumentation
I am just trying to strengthen the point that orthogonality is not determined by frequency but by phase.
I didn't refer to phase because it's not needed to answer the original question. But it's true that sine and cosine wave of same frequency are orthogonal. Also any harmonic to each other or the DC component.
Your explanation seems to me unnecessary complicated and somehow counterintuitive. You don't need to refer to phase to explain why signal components of different frequency add up by their power rather than magnitude.
I'm aware that orthogonality is a rather general term, different science disciplines may possibly use it in a different sense.

28th July 2019, 22:36 #33
 Join Date
 Aug 2015
 Posts
 1,738
 Helped
 650 / 650
 Points
 10,751
 Level
 24
Re: ELECTRICAL AND ELECTRONICS Instrumentation
RMS = SQRT(RMSA^2 + RMSB^2) is correct but A and B must be 90 degrees out of phase
are you implying that for 45 deg out of phase  vector addition won't work ... ?

29th July 2019, 04:30 #34
 Join Date
 Aug 2016
 Posts
 493
 Helped
 79 / 79
 Points
 2,788
 Level
 12
Re: ELECTRICAL AND ELECTRONICS Instrumentation
presumably if they are in phase the vector addition works too...? ( simple addition works in this case too  as it does for the 180 deg case )
are you implying that for 45 deg out of phase  vector addition won't work ... ?… I acknowledge the fact that vector addition is correct in all cases as mentioned by Easy peasy…
RMS = SQRT(RMSA^2 + RMSB^2) is a specific case of vector addition for two sinusoidal functions with one 90 degrees out of phase with the other, Acosx + Bsinx, and so is not suitable for use as a general expression. RMS = SQRT(RMSA^2 + RMSB^2) obviously does not work for two waveforms that are 45 degrees out of phase with each other.
Akanimo.

Advertisement

29th July 2019, 09:49 #35
 Join Date
 Aug 2015
 Posts
 1,738
 Helped
 650 / 650
 Points
 10,751
 Level
 24
Re: ELECTRICAL AND ELECTRONICS Instrumentation
yes, works for uncorrelated waveforms ...
+ Post New Thread
Please login