+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Full Member level 3
    Points: 1,132, Level: 7

    Join Date
    Jan 2018
    Posts
    183
    Helped
    1 / 1
    Points
    1,132
    Level
    7

    MOSFET Speed and power tradeoff

    Hi I was reading this document and came across some confusion.
    https://www.uio.no/studier/emner/mat...cting_uCox.pdf

    https://www.google.com/search?q=capa...0OqxKbzpedvkM:

    1.As per the above curve, MOS capacitance is small in depletion mode (when 0
    2.When Vgs>Vt, the MOSFET enters into strong inversion mode (Saturation region). Then based on chose Vgs value Id is driven, which decides the Power consumed by the device. The more is the chosen Vgs, the more will be power consumption. In this the MOS capacitance is higher than the above case, so less speed.

    But in the document it is said that
    Always put your transistor in moderate-inversion region (V OV ≈ 150-250 mV) to make a compromise between speed and power consumption. If you need more speed → Strong inversion region. If you want low power → weak inversion

    Can someone tell me
    1.what are exact range for weak, moderate and strong inversion modes.
    2.As per my argument, we get more speed in depletion or weak inversion mode but as per the document it is strong inversion region. Which is correct and why?

    •   AltAdvertisement

        
       

  2. #2
    Newbie level 5
    Points: 696, Level: 5

    Join Date
    Mar 2016
    Posts
    10
    Helped
    7 / 7
    Points
    696
    Level
    5

    Re: MOSFET Speed and power tradeoff

    Dear circuitking,
    the range of the MOS operating region can be determined by gm over Id ratio (gm/ID=2/(VGS-VT)). Hence, if gm is in the range 5-10 S/A the MOS operates in strong inversion, the range 10-15 S/A is the moderate inversion and 15-25 S/A is the weak inversion. The MOS exhibits the maximum speed in strong inversion because it depends by the total gate capacitance that is minimum in this region. I suggest to read about the gm/id methodology in which the mos performance are arranged in lookup tables as function of the gm/ID ratio.
    I hope that it is useful

    Regards


    2 members found this post helpful.

    •   AltAdvertisement

        
       

  3. #3
    Full Member level 3
    Points: 1,260, Level: 8

    Join Date
    Jan 2019
    Location
    Belgium
    Posts
    183
    Helped
    75 / 75
    Points
    1,260
    Level
    8

    Re: MOSFET Speed and power tradeoff

    For a long channel MOSFET, the
    If you increase the overdrive, then your transit frequency goes up. But because transconductance is given by , increasing overdrive decreases the gm(of course make sure you don't change the current).



    •   AltAdvertisement

        
       

  4. #4
    Full Member level 1
    Points: 1,354, Level: 8

    Join Date
    Mar 2015
    Location
    USA
    Posts
    111
    Helped
    20 / 20
    Points
    1,354
    Level
    8

    Re: MOSFET Speed and power tradeoff

    Just to clarify something, strong inversion is not the same as saturation. Strong inversion is the point where you have significantly overcome the surface potential and have created an inversion channel between the drain/source. The gate voltage applied is what creates this channel—that is why SI is definite by a gate voltage. Saturation is given by the drain to source voltage, vov=vgs-vt.


    If you do not have significant vds, you will be in strong inversion, triode. If you surpass the saturation voltage then you will be in strong inversion, saturation.



  5. #5
    Full Member level 3
    Points: 1,260, Level: 8

    Join Date
    Jan 2019
    Location
    Belgium
    Posts
    183
    Helped
    75 / 75
    Points
    1,260
    Level
    8

    Re: MOSFET Speed and power tradeoff

    Quote Originally Posted by vivekroy View Post
    For a long channel MOSFET, the
    If you increase the overdrive, then your transit frequency goes up. But because transconductance is given by , increasing overdrive decreases the gm(of course make sure you don't change the current).
    I don't know why the equations came as elektroda.pl :(

    But here is the answer with the expressions:

    For a long channel MOSFET, the f_T = \frac{1.5\mu}{2\pi L^2}(V_{gs}-V_{th}}
    If you increase the overdrive, then your transit frequency goes up. But because transconductance is given by \frac{2I_D}{V_{gs}-V_{th}}, increasing overdrive decreases the gm(of course make sure you don't change the current).



    •   AltAdvertisement

        
       

  6. #6
    Super Moderator
    Points: 52,642, Level: 56

    Join Date
    Apr 2011
    Location
    Minneapolis, Minnesota, USA
    Posts
    12,884
    Helped
    2571 / 2571
    Points
    52,642
    Level
    56

    Re: MOSFET Speed and power tradeoff

    Quote Originally Posted by vivekroy View Post
    I don't know why the equations came as elektroda.pl
    Your equations were set off by a 'tex' html tag. Apparently the system didn't know how to interpret this, so it defaulted to a logo from our image server as a way of saying 'technical difficulties'.



--[[ ]]--