+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Newbie level 4
    Points: 353, Level: 4

    Join Date
    Feb 2018
    Posts
    7
    Helped
    0 / 0
    Points
    353
    Level
    4

    Broken RF ground plane

    Hi all,

    I'm designing PCB and I have 2 SMA connectors - in, out. Unfortunately, I have to route 3 signals for LEDs under (bottom layer) the coplanar waveguide which providing path to the RF signal (top layer).

    Do you have any tips to do it most "correctly"?. Should the LEDs signal be placed together, should be some bigger space between them?

    I'm telling myself, that when using coplanar waveguide, broken RF ground plane in bottom layer will not cause so much trouble, because I still have "top ground".

    Click image for larger version. 

Name:	ground_plane.png 
Views:	4 
Size:	10.1 KB 
ID:	153801

    Thank you for the answer

    •   AltAdvertisement

        
       

  2. #2
    Advanced Member level 5
    Points: 14,456, Level: 29

    Join Date
    Apr 2014
    Posts
    2,256
    Helped
    903 / 903
    Points
    14,456
    Level
    29

    Re: Broken RF ground plane

    Quote Originally Posted by milansedlak View Post
    I'm telling myself, that when using coplanar waveguide, broken RF ground plane in bottom layer will not cause so much trouble, because I still have "top ground".
    Sounds reasonable, just connect top and bottom near the gap. Another option would be to place a capacitor with suitable SRF across the slot, or a 0R resistor, so that RF can pass.
    Last edited by volker@muehlhaus; 18th June 2019 at 15:14.



    •   AltAdvertisement

        
       

  3. #3
    Advanced Member level 5
    Points: 30,756, Level: 42
    BigBoss's Avatar
    Join Date
    Nov 2001
    Location
    Turkey
    Posts
    4,512
    Helped
    1359 / 1359
    Points
    30,756
    Level
    42

    Re: Broken RF ground plane

    Don't cut the GND plane, connect the LEDs' wires by jumpers over CPWG in air..( put at least 5mm or more height and use rigid jumper wires.)



    •   AltAdvertisement

        
       

  4. #4
    Advanced Member level 5
    Points: 34,110, Level: 45

    Join Date
    Oct 2001
    Posts
    4,868
    Helped
    1447 / 1447
    Points
    34,110
    Level
    45

    Re: Broken RF ground plane

    0R resistors is the answer..choosing their optimum size allow routing an RF signal between terminal pads without problems.



  5. #5
    Member level 5
    Points: 711, Level: 5

    Join Date
    Aug 2018
    Posts
    92
    Helped
    25 / 25
    Points
    711
    Level
    5

    Re: Broken RF ground plane

    I would think your idea is correct. A small gap in the bottom plane should not change the impedance significantly since there is still a solid plane in the top layer. 1mm gap should be wide enough to let three 0.07mm tracks to go through.
    Of course you should use enough GND vias to connect the planes in top and bottom layer together, especially along the both sides of the gap.

    In addition you have an IMN there, the little distortion caused by the gap could be easily remedied by the IMN. If you are really worried, Vfone's method is a very good solution. Use big 0R resistors as bridges for the LED signals. Place a wide enough GND track in the bottom layer underneath the RF track to function as the reference plane. Three~five times of the dielectric material height is sufficient.
    Last edited by cariban; 19th June 2019 at 09:16.



    •   AltAdvertisement

        
       

  6. #6
    Newbie level 4
    Points: 353, Level: 4

    Join Date
    Feb 2018
    Posts
    7
    Helped
    0 / 0
    Points
    353
    Level
    4

    Re: Broken RF ground plane

    Thank you very much for the answers. I will pick one of the method you've mentioned.



--[[ ]]--