+ Post New Thread
Results 1 to 3 of 3
  1. #1
    Newbie level 1
    Points: 93, Level: 1

    Join Date
    Jan 2019
    Location
    St.Petersburg, RF
    Posts
    1
    Helped
    0 / 0
    Points
    93
    Level
    1

    How to build current source based on modified Hawland current pump for 150 mA?

    Hi,

    I have a problem with building of the voltage controlled current source with obligatory grounded load. The input control voltage is in the range from 0 to 5 V, the output voltage is up to 20 V and output current on the load up to 150 mA. The load is some semiconductor device( or material), the (light-emitting)diode for example. Other very important requirements are that the load must be grounded, the control voltage on input and the voltages on the output should be measured with respect to the one common point(ground).

    I have already used the modified Howland current pump. The scheme is quite good for output current of 25 mA, but the suitable heat sink was required to protect the OpAmp. Also I have used the unipolar voltage supply of the OpAmp to obtain the 20 V of output. The another benefit of this scheme is that the output current does not depend on the load resistance.
    Click image for larger version. 

Name:	Sheme04.jpg 
Views:	3 
Size:	448.0 KB 
ID:	153780
    How to modify the Howland current pump with the grounded load for output current up to about 200 mA (150 required with about 10 -40 mA in reserve)?

    I have found the example of such modification in the Ref. https://www.edn.com/design/analog/44...current-source. The Howland current pump based, with n-channel FET switch.
    Click image for larger version. 

Name:	f1x600.jpg 
Views:	5 
Size:	10.7 KB 
ID:	153781
    Figure from Ref. https://m.eet.com/media/1181840/f1x600.jpg
    I have tried this scheme with OpAmp LM324 and FET IRLB8743, using resistors R1=R2=R3=100 kOhm, R4=104 kOhm, and obtain the output current up to 200 mA by varying of R5 (pot of 5 kOhm) controlling resistor.
    But as I found from the circuit calculations, presented in the Ref, the output current is dependent on the load resistance. Hence, this current source is quite bad.

    It is possible to improve the scheme to resolve this problem and to obtain voltage controlled current source with grounded load for output current up to about 150-200 mA?

    •   AltAdvertisement

        
       

  2. #2
    Advanced Member level 2
    Points: 4,410, Level: 15

    Join Date
    Nov 2013
    Posts
    660
    Helped
    169 / 169
    Points
    4,410
    Level
    15

    Re: How to build current source based on modified Hawland current pump for 150 mA?

    Quote Originally Posted by DX400v2 View Post
    I have tried this scheme with OpAmp LM324 and FET IRLB8743, using resistors R1=R2=R3=100 kOhm, R4=104 kOhm, and obtain the output current up to 200 mA by varying of R5 (pot of 5 kOhm) controlling resistor.
    But as I found from the circuit calculations, presented in the Ref, the output current is dependent on the load resistance. Hence, this current source is quite bad.
    By the equation from you (I didn't check) if you set R5=R4-R2 it should handle the load dependence.
    I think your input source at Vin has a varying internal resistance maybe. How you generate Vin?
    "Try SCE to AUX." /John Aaron/



    •   AltAdvertisement

        
       

  3. #3
    Super Moderator
    Points: 257,530, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    44,940
    Helped
    13665 / 13665
    Points
    257,530
    Level
    100

    Re: How to build current source based on modified Hawland current pump for 150 mA?

    Varying R5 is not feasible if you want current source characteristic. The equations for Howland current source have been frequently discussed at Edaboard, e.g. in this thread
    https://www.edaboard.com/showthread....current-source



--[[ ]]--