Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Push button with Pull Up

Status
Not open for further replies.

ansh11

Member level 4
Joined
Feb 27, 2018
Messages
71
Helped
0
Reputation
0
Reaction score
0
Trophy points
6
Activity points
659
I am trying to make PCB board on Eagle CAD

pushhbu.jpg

I don't see the required component in eagle library

How to make PCB board for my circuit?
 

which component are you talking about?

the resistor?
the push button?
the connector?

the resistor:
click on new part
scroll down to rcl library
if you like european symbols, use R-EU_ (resistors look like rectangles with leads)
if you like american symbols, use R-US_ (resistors look like triangle wave with leads)
then resistors are listed by size so:
0204/5 is 2 mm by 4 mm case size with 5 mm between through hole pins
is there is a V after the numbers, the case is mounted vertically, like a tower, rather than the usual horizontally
pick the correct size based on the dimensions of your chosen resistor

the push button:
at the bottom of library list, put "push" (without quotes) in search box
use something from swich library
OR
go to switch library and look around a little

the connector looks like
Phoenix Contact COMBICON MC, 3.81mm Pitch, 3 Way, 1 Row, Right Angle PCB Terminal Block Header, 1803280
look in the con-phoenix-(size) library, where size is the correct pin spacing
 
  • Like
Reactions: ansh11

    ansh11

    Points: 2
    Helpful Answer Positive Rating
which component are you talking about?

the resistor?
the push button?
the connector?

the connector looks like
Phoenix Contact COMBICON MC, 3.81mm Pitch, 3 Way, 1 Row, Right Angle PCB Terminal Block Header, 1803280
look in the con-phoenix-(size) library, where size is the correct pin spacing

many thanks wwfeldman

I see this package for push button

TOGGLE SWITCH

Footprint: MS243 (Version 1)
TOGGLE SWITCH

3D Package: MS243 (Version 1)

I do not find Phoenix Contact COMBICON MC in library I have downloaded it https://github.com/chiengineer/Eagle-Libraries/blob/master/Connectors/con-phoenix-508.lbrand placed under C:\Users\ansh\Documents\EAGLE\libraries

How to add this part in the library?
 

I do not find Phoenix Contact COMBICON MC in library I have downloaded
Would be in xx381 not xx508 library. If this particular type isn't supported, use the next best 3.81 mm 3 pin connector.
 

@ansh11
a toggle switch is not a push button
a toggle switch, in its simplest form, is an on off switch
the switch in your photograph is a momentary contact push button - likely close on push

the phoenix contact library is not listed that way - its listed as con-phoenix-(size)
were size is a three digit number, like 381, or 58 as FvM points out
 

Would be in xx381 not xx508 library. If this particular type isn't supported, use the next best 3.81 mm 3 pin connector.

I have downloaded libray xx381

phonix2.jpg

Will this suitable?

- - - Updated - - -

@ansh11
a toggle switch is not a push button
a toggle switch, in its simplest form, is an on off switch
the switch in your photograph is a momentary contact push button - likely close on push

the phoenix contact library is not listed that way - its listed as con-phoenix-(size)
were size is a three digit number, like 381, or 58 as FvM points out

so I downloaded library switch-tact for push button **broken link removed**

and placed under C:\Users\ansh\Documents\EAGLE\libraries

but when I search switch-tact I don't get it

switch2f.jpg
 

Will this suitable?
The selected component has apparently 2.54 mm pin distance, indicated both by the name and the ruler. Having it in a xx381 library seems erroneous.

Personally I'm rarely using predefined libraries, defining the required components myself. It's easy and straightforward in most CAD tools.
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top