+ Post New Thread
Results 1 to 15 of 15
  1. #1
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Common mode noise reduction by connecting ferrite SMPS core to ground?

    Hello,
    How much better improvement would you expect to get in common mode emissions in a 30W offline flyback by connecting the ferrite core to primary circuit ground?
    Here it is specified on the transformer winding spec diagram…
    https://imgur.com/rdqzATJ

  2. #2
    Advanced Member level 5
    Points: 38,586, Level: 48

    Join Date
    Mar 2008
    Location
    USA
    Posts
    6,245
    Helped
    1809 / 1809
    Points
    38,586
    Level
    48

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    None, since ferrite is hardly conductive.


    1 members found this post helpful.

    •   AltAdvertisment

        
       

  3. #3
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    Thanks, do you know why it is done?
    The diagram in the top post is of a transformer which exists inside a totally sealed plastic enclosure, so it wouldnt have been done for safety reasons.
    (The pin2 in the diagram, gets connected to circuit ground....and this gets connected to the ferrite core)

    The picture in the top post is of a offline transformer which is today used in 100's of thousands of consumer products...
    Last edited by treez; 14th April 2019 at 10:05.



  4. #4
    Super Moderator
    Points: 253,760, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    44,210
    Helped
    13455 / 13455
    Points
    253,760
    Level
    100

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    Nothing shown about the transformer. Why do you assume it's a ferrite core?


    1 members found this post helpful.

  5. #5
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    Thanks, i used to work at the company and i know this is the ferrite core of an offline 70w flyback smps.



  6. #6
    Super Moderator
    Points: 253,760, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    44,210
    Helped
    13455 / 13455
    Points
    253,760
    Level
    100

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    I know this is the ferrite core of an offline 70w flyback smps
    How is it connected?


    1 members found this post helpful.

  7. #7
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    thanks, i will find out when i get back to where it is kept on monday...as i remember there is a kind of metal plate stamped to the ferrite, and this is wired to pin2 of the transformner bobbin...but i will check monday



    •   AltAdvertisment

        
       

  8. #8
    Advanced Member level 5
    Points: 15,858, Level: 30

    Join Date
    Nov 2012
    Posts
    2,909
    Helped
    701 / 701
    Points
    15,858
    Level
    30

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    i used to work at the company and i know this is the ferrite core of an offline 70w flyback smps. ...
    Ferrites are iron and other metal oxides and you cannot solder or weld to this.

    They are mostly spinel but that is immaterial. You cannot ground a non-conductor. They are very hard (you cannot drill but you can use a grinder) but also very brittle.

    Because they are non-conductor, they do not have eddy losses. They have some hysteresis loss but that too is small compared to iron (or other magnetic materials).

    Sometimes mistakes do get propagated (because no one questions them) - like genetic errors. You can attach a wire using a silver paste (to the core) but that serves no practical purpose.

    Sometimes you may want to screen the whole transformer by enclosing it in a copper mesh. But that is a different story.

    Or, am I missing some other point???


    2 members found this post helpful.

  9. #9
    Advanced Member level 5
    Points: 15,858, Level: 30

    Join Date
    Nov 2012
    Posts
    2,909
    Helped
    701 / 701
    Points
    15,858
    Level
    30

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    this is wired to pin2 of the transformner bobbin...but i will check monday
    Sometimes a screen is placed between the primary and secondary windings; a copper foil or a mesh is commonly used. They must not close a loop and if the mesh (or foil) is grounded, it prevents electrostatic induction (capacitance in other words) between the primary and secondary. The foil or mesh, if closed (forms a loop), will prevent the magnetic induction to work (it will form a virtual shorted secondary winding). The screen is quite effective if grounded. But it does not connect to the magnetic core and you need to check carefully the connections.


    1 members found this post helpful.

  10. #10
    Super Moderator
    Points: 253,760, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    44,210
    Helped
    13455 / 13455
    Points
    253,760
    Level
    100

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    treez has been discussing a lot about about interwinding shields, I presume he knows the difference. The question is definitely not about interwinding shield.


    1 members found this post helpful.

  11. #11
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    How is it connected?
    Primary side ground is actually connected to the ferrite core by way of a 3cm bare copper wire which is taped to the underside of the ferrite core. the end of the bare copper wire is soldered to pin 2 of the bobboin, which itself is soldered into primary ground.
    Do you know why the ferrite is connected to primary side ground?



  12. #12
    Advanced Member level 5
    Points: 38,586, Level: 48

    Join Date
    Mar 2008
    Location
    USA
    Posts
    6,245
    Helped
    1809 / 1809
    Points
    38,586
    Level
    48

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    Wonder whether this is a "legacy" from days when a
    stamped steel core was used, and nobody thought to
    delete the now-useless bit? I have seen laminated-
    core xfmrs with a pigtail.


    1 members found this post helpful.

  13. #13
    Advanced Member level 5
    Points: 15,858, Level: 30

    Join Date
    Nov 2012
    Posts
    2,909
    Helped
    701 / 701
    Points
    15,858
    Level
    30

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    Do you know why the ferrite is connected to primary side ground?
    It is not correct to describe this as a connection; the ferrite body is an insulator and one cannot connect electrically to an insulator. It serves no electrical purpose.

    Some mistakes can be hereditary...


    1 members found this post helpful.

  14. #14
    Advanced Member level 5
    Points: 31,540, Level: 43
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    cambridge
    Posts
    6,594
    Helped
    477 / 477
    Points
    31,540
    Level
    43

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    The thing is (on a related subject) people often talk about winding torroids so that there is minimal capacitive coupling of the wire to the core...........and so what this "pigtail" does, i believe, is capacitively couple the core to primary ground...for the purpose of common mode noise reduction. Do you agree?
    It cant be an accident, this transformer was wound by an enormous, and sucessful Chinese SMPS company.
    Also, the small 1W transformer also has the core similaraly connnected.



    •   AltAdvertisment

        
       

  15. #15
    Advanced Member level 5
    Points: 15,858, Level: 30

    Join Date
    Nov 2012
    Posts
    2,909
    Helped
    701 / 701
    Points
    15,858
    Level
    30

    Re: Common mode noise reduction by connecting ferrite SMPS core to ground?

    capacitive coupling of the wire to the core...
    Yes, there will always be some capacitive coupling between the winding and the core (even if it is air-cored).

    Assume for the sake of this discussion that the core is metal. Then the insulation between the core and the winding makes the dielectric. The core and the winding can be considered the two foils of the capacitor.

    Do you change the capacitance if you ground one of the two ends (of a capacitor)? Say if you ground the core of a iron cored transformer (it will still be tricky because the laminations are insulated), what will be the effect?

    The thinner the dielectric, the greater is the electric field and the capacitance. We cannot increase this thickness arbitrarily for practical reasons.

    Assume now that the core is an insulator. The core now is the dielectric. And the bare (it does not matter whether it is bare or not) copper wire is now the other electrode of the capacitor.

    Because the solid core now acts as the dielectric, the capacitance will now be less. But how much effect you will see if you ground the other end?

    In particular, as the copper wire does not go around the core, I cannot guess the overall effect.

    But anyway, the core is not grounded simply because it is non-conducting.


    1 members found this post helpful.

--[[ ]]--