+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Full Member level 6
    Points: 4,514, Level: 15
    Externet's Avatar
    Join Date
    Jan 2004
    Location
    Mideast US
    Posts
    383
    Helped
    26 / 26
    Points
    4,514
    Level
    15

    Circuit to detect presence of a single RF frequency ?

    Hi.
    -Detection here not meaning to demodulate-
    Detection as to know if 10.7MHz ± 100KHz is present on an existing receiver circuit node, to turn a LED on. How should be done ? Any dedicated IC or portion of such that does/could do it ?
    Abolish the deciBel !

    •   AltAdvertisement

        
       

  2. #2
    Advanced Member level 5
    Points: 29,511, Level: 41
    BigBoss's Avatar
    Join Date
    Nov 2001
    Location
    Turkey
    Posts
    4,289
    Helped
    1298 / 1298
    Points
    29,511
    Level
    41

    Re: Circuit to detect presence of a single RF frequency ?

    A simple amplifier then a ceramic 10.7MHz filter following a amplifier+comparator will turn-on the LED.
    Even an OPAMP may work with a appropriate circuit combination.There are many choices..



    •   AltAdvertisement

        
       

  3. #3
    Advanced Member level 2
    Points: 4,410, Level: 15

    Join Date
    Nov 2013
    Posts
    660
    Helped
    168 / 168
    Points
    4,410
    Level
    15

    Re: Circuit to detect presence of a single RF frequency ?

    I don't know how can a LED turn on with such a high frequency, I think a mixer + 10MHz oscillator + low-pass filter + amplifier rather capable.
    SA612 could be good because it contains mixer and oscillator.
    "Try SCE to AUX." /John Aaron/



    •   AltAdvertisement

        
       

  4. #4
    Super Moderator
    Points: 79,807, Level: 68
    Achievements:
    7 years registered
    Awards:
    2nd Helpful Member
    betwixt's Avatar
    Join Date
    Jul 2009
    Location
    Aberdyfi, West Wales, UK
    Posts
    13,063
    Helped
    4372 / 4372
    Points
    79,807
    Level
    68

    Re: Circuit to detect presence of a single RF frequency ?

    Use a PLL and connect the LED to the lock indicator. By changing the VCO components you can set the center frequency and by changing the loop components you can set the lock bandwidth.

    Brian.
    PLEASE - no friends requests or private emails, I simply don't have time to reply to them all.
    It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.



  5. #5
    Member level 5
    Points: 588, Level: 5

    Join Date
    Aug 2018
    Posts
    80
    Helped
    22 / 22
    Points
    588
    Level
    5

    Re: Circuit to detect presence of a single RF frequency ?

    HMC1120 from analog can do the work. It is may be over-qualified.
    https://www.analog.com/media/en/tech...ts/hmc1120.pdf

    You may need to put a bandpass filter to just detect the 10.7MHz signal.



    •   AltAdvertisement

        
       

  6. #6
    Advanced Member level 5
    Points: 34,203, Level: 45

    Join Date
    Dec 2004
    Location
    New England, USA
    Posts
    4,808
    Helped
    1347 / 1347
    Points
    34,203
    Level
    45

    Re: Circuit to detect presence of a single RF frequency ?

    Quote Originally Posted by BigBoss View Post
    A simple amplifier then a ceramic 10.7MHz filter following a amplifier+comparator will turn-on the LED.
    Even an OPAMP may work with a appropriate circuit combination.There are many choices..
    i would modify this...ceramic filter, amplifier with 15 db gain at 10.7 MHz, another ceramic filter, then a schottky diode detector. The DC output of the detector can drive a comparator with a TTL output, that you could add a resistor limited LED to.

    by using TWO ceramic filters...you can get almost 60 dB rejection of other frequencies.



--[[ ]]--