+ Post New Thread
Results 1 to 9 of 9

8th February 2019, 15:12 #1
 Join Date
 Jan 2012
 Location
 Italy
 Posts
 871
 Helped
 40 / 40
 Points
 5,017
 Level
 16

Advertisement

23rd February 2019, 21:24 #2
 Join Date
 Sep 2008
 Location
 Germany
 Posts
 8,077
 Helped
 2654 / 2654
 Points
 51,703
 Level
 55
Re: Slew rate for folded OPAMP with driver
Like always, the slew rate δV/δt = Iout/Cout .
The current Iout of the output buffer is the adjusted current Ipre of the preamp stage (through M12, M10 ...) times the current gain by the W/L ratio(s) between the output and preampstage Iout/Ipre = (W/L(MON))/(W/L(M10)) , or the ratio of the corresponding pchannel transistors  if different, take the smaller one for the Iout calculation.
Cout, selfevident, is the load capacitance Cload, plus the feedback capacitance (= compensation cap, in your case) times this gain factor (if different for p and nchannel, take the bigger one, in this case).
1 members found this post helpful.

25th February 2019, 15:52 #3
 Join Date
 Jan 2012
 Location
 Italy
 Posts
 871
 Helped
 40 / 40
 Points
 5,017
 Level
 16
Re: Slew rate for folded OPAMP with driver
Dear Erikl
Thank you very much for your reply,
Actually I am little confused, because you are mentioning the load capacitor in the calculation.... but if I understand it this way, I would say that for my OpAmp the slew rate is not limited to the external capacitor, it is limited to the compensation capacitor as I can get confirmed by my simulation.
for my circuit, I am designing the floating current source of 50 uA and my compensation capacitor is 0.64 PF. if I would use the equation δV/δt = Iout/Cout = 50uA/0.64 PF it should give me Slew rate = 78 V/uS. However I am getting in my simulation only 48 V/uS.
Please correct me if I am wrong and thank you once again.

25th February 2019, 16:29 #4
 Join Date
 Nov 2013
 Posts
 660
 Helped
 168 / 168
 Points
 4,410
 Level
 15
Re: Slew rate for folded OPAMP with driver
The classAB output stage should handle the high chargeup current of the load capacitor, you can check it easily by comparing with or without load capacitor (the slewrate).
I think you are right when you calculate only with the compensation capacitor, because the 1st stage of your OPAmp will see only that and those current is limited by the preamplifier.
48V/us is quite close to your expected 78V/us, don't trust in Spice level 1 equations for different parameters. These are useful to estimate things but the simulation of BSIM3,BSIM4 level devices will give you much accurate answer.
Possible reasons of difference could be:
1, you are using nonlinear compensation capacitor
2, the 1st stage current sources are not exactly 50uA biased
3, wrong formula...I haven't checked it analytically..."Try SCE to AUX." /John Aaron/
1 members found this post helpful.

Advertisement

25th February 2019, 17:30 #5
 Join Date
 Jan 2012
 Location
 Italy
 Posts
 871
 Helped
 40 / 40
 Points
 5,017
 Level
 16
Re: Slew rate for folded OPAMP with driver
Dear frankrose,
Thank you for your comment,
So me and you are agreed with the point that the slew rate is limited to the preamplifieer, as the output amplifier can sufficiently drive the external capacitor,
I would only answer one of your points, I am not using spice level one in my simulation, I am using the BSIM3 or BISM4 modules.
I am just thinking of one thing, if you look back to the figure you see where the compensation capacitor is inserted, may be it helps,,

25th February 2019, 21:54 #6
 Join Date
 Sep 2008
 Location
 Germany
 Posts
 8,077
 Helped
 2654 / 2654
 Points
 51,703
 Level
 55
Re: Slew rate for folded OPAMP with driver
I think you must consider the output capacitance of the driving node (the output), too, in parallel. You could try it by adding a cap (to GND).
###############
BTW: Pls. adhere to the official lower case for the abbreviation of pico (pF) and of second, here V/µs .
V/µS means Volt per microSiemens, which would end up in V²/µA
1 members found this post helpful.

26th February 2019, 10:28 #7
 Join Date
 Jan 2012
 Location
 Italy
 Posts
 871
 Helped
 40 / 40
 Points
 5,017
 Level
 16
Re: Slew rate for folded OPAMP with driver
Dear Erikl,,
Thank you once again,
The problem is that I need to write the equation in my work, and therefore I need the mathematical expression for the slew rate.
Second thing please, I can design the floating current source with any value, in the book of Jakob he is designing it to be half of the tail current of the differential pairs, so I just want to know for this circuit is there rule for this amount.
In normal folded cascode circuit we usually bias the folded transistor with a current equal to the tail current and that is obvious why, but with folded using floating source with up and down mirror like this circuit I see I can select any value. is it right?
The other question why this man is using only one compensation capacitor, every one is using two, one for the upper driving transistor and the other for the down one
Thank you once again

26th February 2019, 11:48 #8
 Join Date
 Nov 2013
 Posts
 660
 Helped
 168 / 168
 Points
 4,410
 Level
 15
Re: Slew rate for folded OPAMP with driver
It uses one because it is in a book. Not the most practical, but not that is the point.
Others use 2 because in the preamplifier the bottom or top current mirrors can enter into triode region, not at the same time. So at output signal transition the response is better with 2 caps, because 1 of them will be always connected to a mirror which is in saturation.
Sometimes these caps are MOS varactors which CV curve is nonlinear. Imagine only 1 cap as on the figure above, and you can see that at low output voltage the compensation cap's value will drop. This can cause ringing at low output, but if you imagine the other cap too you can see the added cap has its highest value at low output voltage, so it can eliminate the ringing."Try SCE to AUX." /John Aaron/
1 members found this post helpful.

Advertisement

28th February 2019, 06:42 #9
 Join Date
 Nov 2001
 Location
 US
 Posts
 786
 Helped
 219 / 219
 Points
 9,195
 Level
 22
Re: Slew rate for folded OPAMP with driver
If you have a comp cap to the upper transistors you'll have the feed forward zero. In this configuration it is hardly a problem because you cab consider the source of the upper transistor as almost ac ground and thus the feedforward action is greatly reduced but it is still there since that upper compensation is in the signal path. Not the case with the lower compensation capacitor.
1 members found this post helpful.
+ Post New Thread
Please login