+ Post New Thread
Results 1 to 5 of 5
  1. #1
    Member level 1
    Points: 2,366, Level: 11
    Achievements:
    Created Blog entry 7 years registered

    Join Date
    Apr 2007
    Posts
    36
    Helped
    1 / 1
    Points
    2,366
    Level
    11
    Blog Entries
    2

    P-channel fet driver problem

    Hello,

    I am trying to figure it out why the following circuit is not working properly in reality while in theory should work. It is a P-CHANNEL FET driver shifting the gate voltage within the limits of the MOSFET.

    The input (R39) is a 5v control signal and in my simulation at R37 it should swing between 8v and 24v. However when I built the circuit, the voltage changed only between 9v and 10 volts (the MOSFET after R37 is removed). When the TIP122 and TIP127 are removed, voltages at the 2N2222A are correct, but when I place the TIP122 and TIP127 the output is only between 9 and 10v.

    I replaced all transistors with new ones and still got the same problem. Any help what am I missing and where could be/is the problem?

    Thank you.

    •   AltAdvertisment

        
       

  2. #2
    Super Moderator
    Points: 78,154, Level: 68
    Achievements:
    7 years registered
    Awards:
    2nd Helpful Member
    betwixt's Avatar
    Join Date
    Jul 2009
    Location
    Aberdyfi, West Wales, UK
    Posts
    12,788
    Helped
    4272 / 4272
    Points
    78,154
    Level
    68

    Re: P-channel fet driver problem

    TIP122/127 are low gain devices, you probably are starving them of base current to get full switching. Also check reverse breakdown voltages on those devices.

    Brian.
    PLEASE - no friends requests or private emails, I simply don't have time to reply to them all.
    It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.



    •   AltAdvertisment

        
       

  3. #3
    Super Moderator
    Points: 72,564, Level: 65
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    14,749
    Helped
    3367 / 3367
    Points
    72,564
    Level
    65

    Re: P-channel fet driver problem

    Hi,

    Why is R39 = 220R while R4 = 1200R?
    I'd rather expect it vice versa.

    Klaus
    Please don´t contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



    •   AltAdvertisment

        
       

  4. #4
    Advanced Member level 5
    Points: 18,461, Level: 32
    Achievements:
    7 years registered
    crutschow's Avatar
    Join Date
    Feb 2012
    Location
    L.A. USA Zulu -8
    Posts
    3,573
    Helped
    844 / 844
    Points
    18,461
    Level
    32

    Re: P-channel fet driver problem

    With that much difference between the sim and real circuit, I suspect a problem with the real circuit wiring.
    Make sure both transistors are wired properly (especially the collector and emitters).
    Zapper
    Curmudgeon Elektroniker



  5. #5
    Member level 1
    Points: 2,366, Level: 11
    Achievements:
    Created Blog entry 7 years registered

    Join Date
    Apr 2007
    Posts
    36
    Helped
    1 / 1
    Points
    2,366
    Level
    11
    Blog Entries
    2

    Re: P-channel fet driver problem

    Quote Originally Posted by crutschow View Post
    With that much difference between the sim and real circuit, I suspect a problem with the real circuit wiring.
    Make sure both transistors are wired properly (especially the collector and emitters).
    Thank you indeed that was the problem. I drew the PCB using the wrong model - 2N2222A instead of MMBT2N2222A - looks like their collector-emitter pins are switched.

    Anyway, the TIP122-TIP127 are darlington pair transistors and now the circuit works exactly as in the simulation and drives the gate between 8v and 24v to keep it within the 20v Vgs limits of the MOSFET.



--[[ ]]--