+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Junior Member level 1
    Points: 2,048, Level: 10
    Achievements:
    7 years registered

    Join Date
    May 2008
    Posts
    19
    Helped
    0 / 0
    Points
    2,048
    Level
    10

    Reverse polarity protection using N-channel MOSFET

    Hi Guys,

    I need to protect my circuit from reverse polarity.
    The relevant part of the circuit if an MPPT charger for a battery.
    The input is a solar panel.

    The voltage of the panel is to high for the MOSFET so I need a Zener diode to reduce the voltage.
    My question is how to connect the Zener in this case?

    I attached two circuits, does it matter if I use the left one or the right one?
    Other ideas or comments are appreciated.

    V+ and V- are the solar panel connections. GND is the circuit GND

    Thanks,
    Tomer

    •   AltAdvertisment

        
       

  2. #2
    Member level 4
    Points: 518, Level: 4

    Join Date
    Aug 2018
    Posts
    71
    Helped
    22 / 22
    Points
    518
    Level
    4

    Re: Reverse polarity protection using N-channel MOSFET

    How is the battery connected?



    •   AltAdvertisment

        
       

  3. #3
    Junior Member level 1
    Points: 2,048, Level: 10
    Achievements:
    7 years registered

    Join Date
    May 2008
    Posts
    19
    Helped
    0 / 0
    Points
    2,048
    Level
    10

    Re: Reverse polarity protection using N-channel MOSFET

    The battery is connected to the MPPT output.
    What you see is the MPPT input.

    See attachment below for the complete circuit (not fully designed yet).

    The question is what is better (if there is any difference) for the Zener.

    Click image for larger version. 

Name:	Reverse Polarity Protection3.JPG 
Views:	13 
Size:	42.7 KB 
ID:	151000



    •   AltAdvertisment

        
       

  4. #4
    Super Moderator
    Points: 253,869, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    44,227
    Helped
    13461 / 13461
    Points
    253,869
    Level
    100

    Re: Reverse polarity protection using N-channel MOSFET

    Zener diode needs to be connected between gate and source to protect the transistor. The other circuit doesn't disconnect a reversed power source at all.

    It's not quite plausible to have an efficient MOSFET protection in the V- line and another series diode in the V+ line.


    1 members found this post helpful.

  5. #5
    Junior Member level 1
    Points: 2,048, Level: 10
    Achievements:
    7 years registered

    Join Date
    May 2008
    Posts
    19
    Helped
    0 / 0
    Points
    2,048
    Level
    10

    Re: Reverse polarity protection using N-channel MOSFET

    Thanks.
    That was helpful.
    As for the diode, you are right - it is a remanent of an old design, it will be removed.



    •   AltAdvertisment

        
       

  6. #6
    Newbie level 4
    Points: 536, Level: 4

    Join Date
    Jun 2016
    Location
    Nigeria
    Posts
    7
    Helped
    1 / 1
    Points
    536
    Level
    4

    Re: Reverse polarity protection using N-channel MOSFET

    My idea here is that: Reverse Polarity can be done using Diode. By rectifying the input with a full bridge rectification, before using N- Channel MOSFET to ensure full flow of current at the right polarity and to avoid diodes voltage. Thanks



--[[ ]]--