+ Post New Thread
Results 1 to 7 of 7
  1. #1
    Member level 3
    Points: 475, Level: 4

    Join Date
    Dec 2017
    Posts
    67
    Helped
    0 / 0
    Points
    475
    Level
    4

    Mosquito Zapper - Different approaches, and circuit diagrams...

    Hello,

    I'm in the process of designing a mosquito zapper. I tried to gather as much details as I can about their theory of operation and popular circuits. I have also a bunch of them here and I have already opened some to take a look at their inner workings. Well, as an embedded designer, I do not get involved a lot in analog circuitry. However, I believe mixing the two distinct domains one can come up with a much better and improved design over what's offered out there.

    From what I noticed so far, some of the cheaper designs had their circuits built around HV caps, diodes, etc. No transformers or ballasts used. A bigger device has more powerful circuitry, transformer-based design, and a ballast for the CFL.

    Now the question is; what are the best practices available today to design such a device? What is the advantage of the transformer-based design over the other one? Is there any way to achieve same results (output power for the arc) without the transformer? How about miniature transformers?

    If you can share some circuits, it would help a lot!

    Thank you!

    •   AltAdvertisment

        
       

  2. #2
    Super Moderator
    Points: 76,044, Level: 67
    Achievements:
    7 years registered
    Awards:
    2nd Helpful Member
    betwixt's Avatar
    Join Date
    Jul 2009
    Location
    Aberdyfi, West Wales, UK
    Posts
    12,439
    Helped
    4143 / 4143
    Points
    76,044
    Level
    67

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    Really cheap Chinese made ones use simple voltage multipliers using a chain of diodes and capacitors. The CFL is a normal inductive ballast. Although there is some voltage in each stage of a voltage multiplier, driven from mains AC they can still produce several KV with only a few low cost components.

    Brian.
    PLEASE - no friends requests or private emails, I simply don't have time to reply to them all.
    It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.



  3. #3
    Member level 3
    Points: 475, Level: 4

    Join Date
    Dec 2017
    Posts
    67
    Helped
    0 / 0
    Points
    475
    Level
    4

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    Hello Brian,

    Thank you. Well, this is one of them I got off the web:

    Click image for larger version. 

Name:	EC5_1_several_Villard_stages_mosquito_zapper.jpg 
Views:	9 
Size:	31.2 KB 
ID:	150682

    [Found at electronicsforu. com/ wp-contents/ uploads/ 2016/ 05/ EC5_1. jpg]

    It's a cheap one built with simple discrete components. However, the output arc of such a circuit doesn't fry all mosquito and some of them escape the mesh after getting shocked. What do you suggest to increase the output voltage, adding more stages to the ladder or replace caps with higher rating ones? If I can achieve better results without the transformer, I would prefer to go that route.

    Thanks
    Last edited by BradtheRad; 10th January 2019 at 06:02. Reason: Converted image to Edaboard attachment



    •   AltAdvertisment

        
       

  4. #4
    Member level 3
    Points: 475, Level: 4

    Join Date
    Dec 2017
    Posts
    67
    Helped
    0 / 0
    Points
    475
    Level
    4

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    By the way, it would be great if you can elaborate more on the CFL circuit and how to make it power different CFL, say 18W, 24W, or smaller ones like 4W.



  5. #5
    Super Moderator
    Points: 76,044, Level: 67
    Achievements:
    7 years registered
    Awards:
    2nd Helpful Member
    betwixt's Avatar
    Join Date
    Jul 2009
    Location
    Aberdyfi, West Wales, UK
    Posts
    12,439
    Helped
    4143 / 4143
    Points
    76,044
    Level
    67

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    You can increase the voltage by simply extending the diode/capacitor chain. For example adding a duplicate of C5,C6, D5, D6 to the end of the existing ones. It doesn't give you something for nothing because the voltage isn't exactly doubled and the current that can flow is also reduced but I doubt a mosquito would care much about that!

    For the CFL, the biggest improvement would be to change from a white to UV tube. It wouldn't look much brighter to our eyes but insects can see further into the UV spectrum where the light seems brighter to them. If you really want to increase the tube power, the most satisfactory solution is to use a choke and starter as in domestic fluorescent fittings or a an electronic starter for normal lamps. You can try changing the value of C7 but it isn't a very predictable way to do it. Increasing the value will cater for more powerful lamps. you probably don't want to change D7 or R6 as these make a crude starter circuit which should work for almost all lamp ratings.
    The value of C7 decides it's reactance '1/(2 * pi * f * C)' which roughly equates to the value of an equivalent resistor doing the same job. 'f' is in Hz and is your AC line frequency, C is in Farads and the result is in Ohms.

    Brian.
    PLEASE - no friends requests or private emails, I simply don't have time to reply to them all.
    It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.



  6. #6
    Member level 3
    Points: 475, Level: 4

    Join Date
    Dec 2017
    Posts
    67
    Helped
    0 / 0
    Points
    475
    Level
    4

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    Thank you Brian!

    By the way, the schematic says the caps C1~C6 are 630 VAC. That means it is rated @ 1 kVDC. Do you think this value is correct?



    •   AltAdvertisment

        
       

  7. #7
    Super Moderator
    Points: 76,044, Level: 67
    Achievements:
    7 years registered
    Awards:
    2nd Helpful Member
    betwixt's Avatar
    Join Date
    Jul 2009
    Location
    Aberdyfi, West Wales, UK
    Posts
    12,439
    Helped
    4143 / 4143
    Points
    76,044
    Level
    67

    Re: Mosquito Zapper - Different approaches, and circuit diagrams...

    AC and DC ratings are not quite the same thing but for low frequencies if you multiply the AC rating by 1.414 (square root of 2) it will give a minimum DC rating that should be safe. So 1KV rating should be fine. Increasing the voltage rating just gives a wider safety margin, it doesn't make the voltage itself any higher.

    Brian.
    PLEASE - no friends requests or private emails, I simply don't have time to reply to them all.
    It's better to share your questions and answers on Edaboard so we can all benefit from each others experiences.



--[[ ]]--