+ Post New Thread
Results 1 to 8 of 8

9th November 2018, 12:03 #1
 Join Date
 Nov 2018
 Posts
 83
 Helped
 1 / 1
 Points
 538
 Level
 4
DC Amplification using OpAmp
I have a small signal of 10 mV. I need to amplify it to 4 V which need an amplification factor of 400. I would like to use inverting amplifier whose gain is R2/R1, where R2 is a feedback resistor. I am wondering what is the best practice to get the amplification by a factor of 400.
1 Use one OpAmp to get gain 400. R1 = 100 , R2 = 40 K.
2 Use two OpAmp in series. Each with a gain of 20. R1 = 500, R2 = 10 K.

Advertisement

9th November 2018, 12:20 #2
Awards:
 Join Date
 Apr 2014
 Posts
 15,325
 Helped
 3488 / 3488
 Points
 75,593
 Level
 67
Re: DC Amplification using OpAmp
Hi,
One Opamp. Because itīs DC. A second OPAMP just adds more errors.
The two OPAMP solution is good for AC, when you get problems with to the gainbandwidth limit of a single OPAMP.
****
your calculation is true if the source resistance is way below 100 Ohms.
For exact overall gain calculation you need to add the source_resistance to the input_resistance.
Example:
If your source resistance is 10 Ohms, then combined with your 100R and 40k this gives just a gain of 40k/(10R + 100R) = 363.
If you want a gain of 400 then you need to subtract the source resistance from the (ideally) calculated input resistance. 100R  10R = 90R
KlausPlease donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

9th November 2018, 12:31 #3
 Join Date
 May 2008
 Location
 Germany
 Posts
 5,784
 Helped
 1728 / 1728
 Points
 40,377
 Level
 49
Re: DC Amplification using OpAmp
As an alternative, you have mentioned two inverting opamps in serties. From this, I derive that the sign of the amplification (plus or mins) does not matter, correct?
In this case, why not use a single noninvering opamp stage?
The advantage: Because of the very high input resistance the internal resistance of the signal source does not matter at all.

Advertisement

9th November 2018, 16:20 #4
 Join Date
 Dec 2015
 Location
 Madrid, Spain
 Posts
 1,275
 Helped
 313 / 313
 Points
 7,314
 Level
 20

9th November 2018, 16:48 #5

9th November 2018, 22:54 #6
 Join Date
 Nov 2018
 Posts
 83
 Helped
 1 / 1
 Points
 538
 Level
 4
Re: DC Amplification using OpAmp
Hi,
I am not sure if I understood source resistance. I guess it is the resistance of the source, for example signal generator, right ? Usually the standard signal generator has 50 Ohm output characteristic impedance. Is this what you mean source resistance ?
Is it true for all OpAmps that the input impedance is high and the output impedance is low ?

Advertisement

10th November 2018, 01:17 #7
Awards:
 Join Date
 Apr 2014
 Posts
 15,325
 Helped
 3488 / 3488
 Points
 75,593
 Level
 67
Re: DC Amplification using OpAmp
Hi,
Is this what you mean source resistance ?
Is it true for all OpAmps that the input impedance is high and the output impedance is low ?
But not for the circuit. Especially the inverting circuit. It's input resistance is the 100 ohms resistor.
KlausPlease donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.

10th November 2018, 04:52 #8
+ Post New Thread
Please login