+ Post New Thread
Results 1 to 6 of 6

8th November 2018, 15:27 #1
 Join Date
 Nov 2014
 Posts
 66
 Helped
 0 / 0
 Points
 1,011
 Level
 7

Advertisment

11th November 2018, 08:02 #2
 Join Date
 Oct 2013
 Location
 Sweden
 Posts
 196
 Helped
 67 / 67
 Points
 2,081
 Level
 10
 Blog Entries
 6
Re: Error rate vs. bandwidth
This looks like a very carelessly produced graph (e.g. what is "Bit Rage" supposed to mean?).
Perhaps the xaxis is supposed to be related to bit rate. Given a fixed baud rate, higher bit rates will usually lead to higher bit error probability (e.g. think about 64QAM vs BPSK).
However, I usually find that it is not worth wasting your time trying to understand badly presented information like this. If the author isn't even capable of producing a basic graph, then there is a good chance that whatever they are trying to tell you is unhelpful or incorrect.

Advertisment

12th November 2018, 02:16 #3
 Join Date
 Jul 2010
 Location
 Sweden
 Posts
 829
 Helped
 339 / 339
 Points
 6,451
 Level
 19
Re: Error rate vs. bandwidth
The diagram is confusing. The Xaxis is the SNR when the bandwidth = bit rate. When the IF is extended to 1.5 * bit rate, the noise will increase by 1.76 dB (assuming white noise) and the actual SNR will go down if the bandwidth already was enough to pass most of the wanted signal.
The diagram basically shows that there is an optimum IF bandwidth for a certain bit rate. If you decrease (obvious, but not shown in the diagram) or increase the IF BW from the optimum value, the error probability goes up.
The optimum bandwidth for a bit rate depends on the modulation method (NRZL PCM/FM in this case).
1 members found this post helpful.

Advertisment

12th November 2018, 20:51 #4
 Join Date
 Oct 2013
 Location
 Sweden
 Posts
 196
 Helped
 67 / 67
 Points
 2,081
 Level
 10
 Blog Entries
 6
Re: Error rate vs. bandwidth
I'm still confused. What bandwidth are we talking about on the xaxis? I'm confused that at the top we have "IF bandwidth = 1.5 times bit rate" and at the bottom we have "bandwidth = bit rate".
Can you describe, for example, what the data point at the top tells us? It looks to me like "The bit error probability when the IF SNR is ~9dB (with bandwidth = bit rate) is ~7e3 when bandwidth = 1.5x bit rate" ... which is obviously nonsense.Last edited by weetabixharry; 12th November 2018 at 21:00.

12th November 2018, 21:08 #5
 Join Date
 Jul 2010
 Location
 Sweden
 Posts
 829
 Helped
 339 / 339
 Points
 6,451
 Level
 19
Re: Error rate vs. bandwidth
I think the Xaxis only shows the SNR for the case "bandwidth = bit rate". The other curve "bandwidth = 1.5 bit rate" can only be used to see the change in error probability when the IF BW is changed.
The SNR will also change, but that value can't be read from the diagram. We can draw the conclusion that the SNR gets worse, since the error probability increases.
To really understand the diagram I think we also need a diagram that plots the SNR as a function of the IF BW. I expect a peak not far from BW = bit rate.
If the wanted signal already "fits" inside the BW, nothing is gained by increasing the BW. The added signal will mostly be noise, so the SNR will be worse.
1 members found this post helpful.

Advertisment

15th November 2018, 12:01 #6
 Join Date
 Nov 2014
 Posts
 66
 Helped
 0 / 0
 Points
 1,011
 Level
 7
Re: Error rate vs. bandwidth
I attached the entire page including this chart. It is an annex of a standard. It seems std_match is correct in terms of optimal IF bandwidth:
The IF bandwidth, for data receivers, should typically be selected so that 90 to 99 percent of the transmitted power spectrum is within the receiver 3decibel (dB) bandwidth.
I suppose the 1.5x bandwidth leads to a higher error rate because more noise is introduced. Is it correct?
Senmeis
+ Post New Thread
Please login