Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

[ARM] TFT LCD ILI9341 8bit data mode problems

Status
Not open for further replies.
E

e.karimi.elc

Newbie level 4
Joined
May 24, 2018
Messages
5
Helped
0
Reputation
0
Reaction score
0
Trophy points
1
Activity points
67
TFT LCD ILI9341 8bit data mode problem

Dear Sirs ,
recently we use TFT LCD with ILI9341 controller in 8bit data mode and a STM32F746 with mikroc compiler.our LCD size is 320*240 pixels , i don't know why we can't write on address higher than 255 ! , and we don't access in bottom of LCD ,
i mean just we can write on 255 * 240 pixels of LCD display ,
would you please check if there is any bug on software on 8bit data mode ?
Thanks and best regards
Ehsan
 

Re: TFT LCD ILI9341 8bit data mode problem

e.karimi.elc said:
... would you please check if there is any bug on software on 8bit data mode ?
Click to expand...

software ????

// ILI9341 screen size
#define ILI9341_TFTWIDTH 240L
#define ILI9341_TFTHEIGHT 320L

you must handle the orientation of LCD ....
You must have enough RAM area to use it..

#define Max_Lcd_Buff 320L*240L //ILI9341_TFTWIDTH * ILI9341_TFTHEIGHT //320L*240L

Can you display a pixel ,with a defined color in this area 255x240..


You must use Integer type to go over 255 !

Code: 
void DrawPixel(uint16_t x1, uint16_t y1, uint16_t color1)
{
   if((x1 >= _maxX) || (y1 >= _maxY)) return;
    SetWindow(x1, y1, x1+1, y1+1);
    OrientCoordinates(x1, y1);
    _writeData(color1 >> 8, color1);
}
 

Re: TFT LCD ILI9341 8bit data mode problem

Dear Paul ,
Thanks for points,
i check all items one by one .

you must handle the orientation of LCD .... has been done
You must have enough RAM area to use it.. has been done

#define Max_Lcd_Buff 320L*240L //ILI9341_TFTWIDTH * ILI9341_TFTHEIGHT //320L*240L we done it INIT subroutine

Can you display a pixel ,with a defined color in this area 255x240.. yes possible but higher than 255 is not possible


You must use Integer type to go over 255 ! yes we use 16 bit integer .


here you can find our sample code
thanks again
Ehsan

Code: 
sbit TFT_RST at GPIOI_ODR.B12;
sbit TFT_RS at GPIOI_ODR.B9;
sbit TFT_CS at GPIOI_ODR.B8;
sbit TFT_RD at GPIOI_ODR.B11;
sbit TFT_WR at GPIOI_ODR.B10;
unsigned int TFT_DataPort at GPIOI_ODR;

LCD_BLEN = 1;
TFT_Set_Default_Mode();

TFT_Init_ILI9341_8bit(240, 320);

TFT_Dot(240, 255, CL_BLACK);

while(1);
 

Re: TFT LCD ILI9341 8bit data mode problem

hello,


show details on LCD Init et Pixel draw
TFT_Init_ILI9341_8bit(240, 320); // are you sure of this order , because if mode is wrong you need (320,240)
TFT_Dot(240, 255, CL_BLACK);
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top