+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Newbie level 6
    Points: 1,000, Level: 7

    Join Date
    Apr 2013
    Posts
    11
    Helped
    0 / 0
    Points
    1,000
    Level
    7

    Three Phase Pump controller_AN 984a

    Hi,

    I am working with three phase pump controller, with AN984a, dspic33fj12MC202, working very fine and delivering out put of 240AC phase to phase at 60Hz, Now I need to have 380AV or 415 AC phase to phase at 50Hz, and I am in need of support

  2. #2
    Super Moderator
    Points: 66,847, Level: 63
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    13,644
    Helped
    3122 / 3122
    Points
    66,847
    Level
    63

    Re: Three Phase Pump controller_AN 984a

    Hi,

    Whatīs exactly the problem?
    * Increasing the power V_Bus voltage? --> show your power stage
    * decreasing the frequency? --> explained in the AN

    Klaus
    Please donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



  3. #3
    Super Moderator
    Points: 249,046, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    43,337
    Helped
    13177 / 13177
    Points
    249,046
    Level
    100

    Re: Three Phase Pump controller_AN 984a

    To achieve 400 VAC phase-to-phase output voltage, you also need 400 VAC input and a power stage designed for 560 V DC link.



  4. #4
    Newbie level 6
    Points: 1,000, Level: 7

    Join Date
    Apr 2013
    Posts
    11
    Helped
    0 / 0
    Points
    1,000
    Level
    7

    Re: Three Phase Pump controller_AN 984a

    hi

    Thank you, Even though bus bar voltage is 450V DC, corresponding output voltage is 240V AC at 60 Hz, I need at least 350V AC as out put phase to phase, what shall I do either in code or in the hard were

    - - - Updated - - -

    Hi,

    I have checked even on 550V DC link but out put is 240V AC phase to phase, by varying the AN3 ratiometrically V & F changes max 240VAC at 60 Hz



  5. #5
    Super Moderator
    Points: 66,847, Level: 63
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    13,644
    Helped
    3122 / 3122
    Points
    66,847
    Level
    63

    Re: Three Phase Pump controller_AN 984a

    Hi,

    I dont see the problem.
    Even though bus bar voltage is 450V DC, corresponding output voltage is 240V AC at 60 Hz,
    Why? How do you come to this conclusion?

    --> Show what you have done so far and how you calculated the value.

    Klaus
    Please donīt contact me via PM, because there is no time to respond to them. No friend requests. Thank you.



  6. #6
    Super Moderator
    Points: 249,046, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    43,337
    Helped
    13177 / 13177
    Points
    249,046
    Level
    100

    Re: Three Phase Pump controller_AN 984a

    Obviously, the voltage limitation is a problem of your software. You need to understand how the modulation index is calculated therein.



--[[ ]]--