+ Post New Thread
Results 1 to 13 of 13

14th April 2018, 04:56 #1
 Join Date
 Oct 2017
 Posts
 15
 Helped
 0 / 0
 Points
 196
 Level
 2
How to calculate the load impedance using ADS2015?
Dear all,
I know this is a very basic issue, but I'm new to ADS and I'd like to make sure my understanding is correct. Below is my schematic in ADS. I'm using Sparameter simulation. I got the values of S11, Z11, Zin in complex number format. I got confused about these terms:
1/ Zin and Z11, which is the input impedance of the circuit (hereafter mentioned as "ZLoad"), meaning the impedance looking towards the structure (including C1,C2,D1 and Term2) from Term 1?
2/ When I tried to calculate ZLoad from S11 using this equation:
Zload = Z0 * (1+S11)/(1S11)
The result was totally different than Zin or Z11! So what kind of impedance the equation will give?
3/ I found an instruction here: https://www.edaboard.com/showthread.php?t=269785.
 For the first method, I'm wondering whether he's talking about this equation:
where Zin is my ZLoad, and ZL is the impedance of the circuit only, exclusive of Term2?
 For the second method (Smith chart) I really do not understand what he was talking about. How can I move towards load from Z11 if I do not know its value??
 At the same time, there is no transmission line in my circuit, which means transmission loss is assumed to be 0. So if I want to follow the above instruction, I have to add a pair of transmission line between Term 1 and the structure?
I hope anyone can help me to make clear these issues. Thank you so much and look forward to any response.

14th April 2018, 08:00 #2
 Join Date
 Nov 2001
 Location
 Turkey
 Posts
 3,923
 Helped
 1179 / 1179
 Points
 27,281
 Level
 40
Re: How to calculate the load impedance using ADS2015?
Zin and Z11 are not the same things.
Zparameters are Open Circuit Parameters so when you're interested in Z11, the second ( and other possible ports) port must be open circuited.
Zin , it's real Input impedance derived from sparameters while all ports are terminated.

Advertisment

14th April 2018, 14:10 #3
 Join Date
 Oct 2017
 Posts
 15
 Helped
 0 / 0
 Points
 196
 Level
 2
Re: How to calculate the load impedance using ADS2015?
Dear BigBoss,
Thank you very much for your comment. My 1st goal of measuring input impedance is to do the matching. My 2nd goal would be to vary the load with a variable input power to find the optimal load for this topology.
There is a very detailed clip (https://www.youtube.com/watch?v=ZUpuvQqK7ho) to teach how to do impedance matching in ADS. I'd like to follow this clip.
From your comment, I think the steps for me to do the matching will be as follows. Please correct me if I'm wrong:
1. Draw the schematic without Term2 (the 2nd port is open circuited). Get Z11.
2. Redraw it without Term1. Get Z22.
3. Model the circuit by a Z2_P Eqn block. Z(1,1) = Z11, Z(2,2) = Z22. Different than the clip, a term2 will be used to terminate the output. I will not do the output matching network.
Question: Do I need to do the output matching network when my design is a voltage multiplier?
4. Start to do the input impedance matching as shown in the clip.
For my 2nd goal, after doing the matching, the Z of Term2 will be a variable within a range. A Harmonic Balance simulation will be used to determine the optimal power transferred from Term1 to Term2 corresponding to each Pin and Z of Term 2 (now it is functioned as a real load in practice).
Will this work? If you are familiar with ADS, please give me some suggestions. Thank you very much and sorry for a lot of questions.

15th April 2018, 04:10 #4
 Join Date
 Nov 2001
 Location
 Turkey
 Posts
 3,923
 Helped
 1179 / 1179
 Points
 27,281
 Level
 40
Re: How to calculate the load impedance using ADS2015?
Forget about Zxx, it's not your concern.
Your circuit will be pretty nonlinear, therefore you should work HB method but I think you have no experiences at all on HB, right ??
I have never seen a Optimum Load Condition for a such circuit, it's essentially a rectifier circuit, not voltage multiplier.
Optimum Load idea is valid if the circuit contains source(s) otherwise it's not possible to talk about a kind of optimum load concept.

Advertisment

15th April 2018, 05:30 #5
 Join Date
 Oct 2006
 Location
 Real Homeless
 Posts
 2,031
 Helped
 563 / 563
 Points
 13,668
 Level
 28
Re: How to calculate the load impedance using ADS2015?
No.
This is a voltage multiplier essentially.
This is a Greinacher Circuit.
https://en.wikipedia.org/wiki/Voltage_doubler
MPPT(Maximum Power Point Tracking) is very common in Rectifier and Voltage Multiplier.
Optimum Load is very important in Rectifier and Voltage Multiplier.Last edited by pancho_hideboo; 15th April 2018 at 05:42.

Advertisment

15th April 2018, 12:26 #6

15th April 2018, 13:34 #7
 Join Date
 Jan 2008
 Location
 Bochum, Germany
 Posts
 42,861
 Helped
 13045 / 13045
 Points
 246,552
 Level
 100
Re: How to calculate the load impedance using ADS2015?
It's obviously a voltage doubling rectifier ("Greinacher" circuit) but that doesn't change the problem in any way, I think.
Optimal load condition could be e.g. asked in the way, that you have a certain input level and vary the load resistance "Term2" for maximum absorbed power. Or you can turn it in an impedance matching problem if Term2 is fixed and you insert a matching network between the source port and the rectifier circuit.
As BigBoss stated, harmonic balance is the usual solution method.

15th April 2018, 13:47 #8

15th April 2018, 19:59 #9

16th April 2018, 00:03 #10

16th April 2018, 03:55 #11

16th April 2018, 04:07 #12

Advertisment

16th April 2018, 04:12 #13
+ Post New Thread
Please login