+ Post New Thread
Results 1 to 14 of 14

30th March 2018, 18:10 #1
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Understanding switched mode power supplies
Hello everyone
Can someone please help me in understanding the right half plane zero problem usually found in switched mode power supplies(SMPS)? Please tell me the problem created by the right half plane zero in
SMPS and solution for the same.

30th March 2018, 22:21 #2
 Join Date
 Dec 2015
 Location
 Madrid, Spain
 Posts
 1,206
 Helped
 290 / 290
 Points
 6,725
 Level
 19
Re: Understanding switched mode power supplies
RHP zero gives a phase inversion, so the output will take the opposite path before returning back to normality. Compensator should not see that, so it must have reduced BW.
1 members found this post helpful.

31st March 2018, 14:50 #3
Re: Understanding switched mode power supplies
It is usually only a problem that comes up with indirect transfer converters, like boost, buckboost and flyback. Operating deep into CCM will make the problem worse, and as stated the crossover must be reduced very low to avoid the RHP zero effects.
2 members found this post helpful.

Advertisment

31st March 2018, 19:40 #4
 Join Date
 Feb 2014
 Posts
 415
 Helped
 151 / 151
 Points
 3,317
 Level
 13
Re: Understanding switched mode power supplies
In plain language a right hand plane zero means that the initial response of the system to a “request” for more voltage is that voltage briefly dips.
It’s like some cars where if you floor the gas the engine will lose power at first before picking up speed.
This is a inherent property of sometopologies but not others.
The bottom line is that while sources feel a need to mention it, it rarely matters unless you’re really trying to push the performance of your system. If loop bandwidth 1/10th or lower of the switching frequency, which is typical, it doesn’t matter.
3 members found this post helpful.

Advertisment

1st April 2018, 06:25 #5
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Re: Understanding switched mode power supplies
How can I lower the crossover?

1st April 2018, 15:43 #6
Re: Understanding switched mode power supplies
You will select the proper feedback value capacitor on the error amplifier opamp to reduce the total gain to 0 dB at the desired crossover frequency.
1 members found this post helpful.

Advertisment

2nd April 2018, 14:07 #7
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Re: Understanding switched mode power supplies
Does reducing the crossover frequency reduce the bandwidth also??

2nd April 2018, 14:47 #8
 Join Date
 Feb 2014
 Posts
 415
 Helped
 151 / 151
 Points
 3,317
 Level
 13

2nd April 2018, 14:54 #9
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Re: Understanding switched mode power supplies
What is the effect on the stability due to the reduced bandwidth? If there is a trade off between stability and bandwidth, then how can it be solved?

Advertisment

4th April 2018, 23:23 #10
 Join Date
 Feb 2014
 Posts
 415
 Helped
 151 / 151
 Points
 3,317
 Level
 13
Re: Understanding switched mode power supplies
No, in power supplies lower bandwidth almost always makes stability easier.
So much time is devoted to studying advanced compensation schemes but actually standard converters can all be stabilized with a 1pole integrator.
So the point of 'fancier' compensation schemes isn't stability  it's stability AND performance (high bandwidth).
1 members found this post helpful.

14th April 2018, 23:25 #11
 Join Date
 Sep 2008
 Location
 cambridge
 Posts
 6,126
 Helped
 455 / 455
 Points
 29,270
 Level
 41
Re: Understanding switched mode power supplies
RHPZ is to be heeded, as you know.
Your crossover frequency shopuld be no more than a third of your rhpz frequency.
The book by Basso gives the rhpz frequency for various converter topologies.
Discontinuous mode converters dont have RHPZ's.
Also, Buck converters dont have RHPZ's.
   Updated   
Also remember that constant off time control means you dont get an RHPZ

16th April 2018, 06:48 #12
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Re: Understanding switched mode power supplies
What are other ways, besides reducing the crossover frequency, to nullify the effect of RHPZ in switched mode power supplies?

16th April 2018, 15:48 #13
 Join Date
 Jan 2011
 Posts
 3,307
 Helped
 1177 / 1177
 Points
 19,982
 Level
 34
Re: Understanding switched mode power supplies
Only two options:
1. Use another topology which doesn't have the RHPZ (buckderived topologies).
2. Don't operate in continuous conduction mode.
If you use a buckboost or boostderived topology in CCM, then the RHPZ will be present, and its effects cannot be "nullified." You can raise the RHPZ frequency somewhat by decreasing your inductance, or just cut your control bandwidth, but obviously those two options have drawbacks.

18th April 2018, 19:23 #14
 Join Date
 Dec 2017
 Posts
 9
 Helped
 0 / 0
 Points
 113
 Level
 1
Re: Understanding switched mode power supplies
can you tell me the value of voltage sources used in the circuit so that we can perform the simulation?
+ Post New Thread
Please login