+ Post New Thread
Results 1 to 4 of 4
  1. #1
    Newbie level 1
    Points: 14, Level: 1

    Join Date
    Oct 2017
    Posts
    1
    Helped
    0 / 0
    Points
    14
    Level
    1

    Rtd Sensing Problem for 1mA accurate source

    hi guys,

    Til now i am sensing the 3 wire rtd with my cypress ic CY8C2845-24PVXI with internal Idac.
    This Idac give me 5V and 1mA accurate source for sensing rtd element. but this ic has less memory so i need to move on other ic for other application but other ic has not a idac internally.

    now i need to generate external 1mA source with same 5V load for same application.i Tried the attached circuit with 5V reference and lM324 IC up to 1 mA source generation level after that i connect my circuit.
    i got only 3.38 V on out put instead of 5V.
    i am also little bit confused about power for LM324 opamp . how can i decide the power level of opamp?


    Click image for larger version. 

Name:	SCe0o.png 
Views:	9 
Size:	46.9 KB 
ID:	141739Click image for larger version. 

Name:	SCe0o.png 
Views:	9 
Size:	46.9 KB 
ID:	141739

    •   AltAdvertisment

        
       

  2. #2
    Super Moderator
    Points: 61,937, Level: 60
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    12,620
    Helped
    2926 / 2926
    Points
    61,937
    Level
    60

    Re: Rtd Sensing Problem for 1mA accurate source

    Hi,

    What's the power supply voltage for the Opamps?

    Did you read the Opamp's datasheet?
    It is no Rail-to-rail Opamp. Datasheet mentiones several times:
    • Large Output Voltage Swing 0 V to V+ − 1.5 V

    Maybe this is your problem?

    Klaus



    •   AltAdvertisment

        
       

  3. #3
    Super Moderator
    Points: 245,688, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    42,684
    Helped
    13007 / 13007
    Points
    245,688
    Level
    100

    Re: Rtd Sensing Problem for 1mA accurate source

    i got only 3.38 V on out put instead of 5V.
    Should be well sufficient for Pt100. Most critical point is minimal low output voltage of LM324, but it's probably O.K. for this circuit.



    •   AltAdvertisment

        
       

  4. #4
    Super Moderator
    Points: 61,937, Level: 60
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    12,620
    Helped
    2926 / 2926
    Points
    61,937
    Level
    60

    Re: Rtd Sensing Problem for 1mA accurate source

    Hi,

    I agree that 3.38V are sufficient.

    But for true resistor calculation you need to know the actual current. I´m not convinced that the circuit gives exact 1mA .. I rather think the OPAMP is saturated at it´s rail limit and the current is somwhere below 1.00mA.
    --> Then the resistor calculation may be wrong.
    ***
    A simpler method is to just use an about appropriate resistor and measeure the voltage drop across this known resistor. Then you may calculate the true current.
    Measure the voltage drop acrross the PT100 and calculate the exact resistance.

    Klaus



--[[ ]]--