+ Post New Thread
Results 1 to 6 of 6
  1. #1
    Full Member level 5
    Points: 2,653, Level: 12
    Achievements:
    7 years registered

    Join Date
    Jan 2012
    Posts
    304
    Helped
    1 / 1
    Points
    2,653
    Level
    12

    What tool do I need for these connectors?

    Take a look at the image attached. I've used a simple plier to crimp the wire to the end-piece (or what you call them), but the result is never good. What type of tool do I need to make reliable connections with these kind of connectors? Or perhaps someone could recommend other types of connectors to be used? I'm just looking for a cheap, simple and reliable way to make connectors that can be connected to pcb's, as an alternative to soldering the wires directly to the board. I'm also not sure what the English names for these connectors and tools are:(


    •   AltAdvertisement

        
       

  2. #2
    Super Moderator
    Points: 77,782, Level: 68
    Achievements:
    7 years registered
    Awards:
    Most Frequent Poster 3rd Helpful Member

    Join Date
    Apr 2014
    Posts
    15,764
    Helped
    3590 / 3590
    Points
    77,782
    Level
    68

    Re: What tool do I need for these connectors?

    Hi,

    please find out which manufacturer and which crimp connector type this is.
    At the manufacturer homepage you will find approriate tools.

    You want it cheap? Often theese tools are far away from beeing cheap.

    But why:
    Those tools need to be producece especially for those crimp connectors... with very tight mechanical tolerance.
    The steel needs to be hardened not to wear out soon.

    A crimp connection is one of the most reliable connection types, but only if it is made correctely.
    It needs a huge ammount of pressure so that the connection between wire and crimp contact is like welded. You can not open a correctely made crimp connection.
    Both wire and crimp contact are "one" piece of metal. Only if this is the case, then you have optimal crimp quality.

    There are many cheap tools on the market.
    * many of the have too low force to make the connection like welded.
    * some of them have not the correct geometry and the press at a plce of the crimp contakt that hurts mechanical stability and the contact may break easily.
    * some of them are not of good quality, not hardened. Maybe the produce good quality at first, but then they soon wear out and the crimp quality decreases. But this is not obvious and you may find out with failures in the field. Not good.

    Klaus

    •   AltAdvertisement

        
       

  3. #3
    Full Member level 4
    Points: 2,844, Level: 12
    Achievements:
    7 years registered

    Join Date
    Feb 2009
    Location
    Kolkata
    Posts
    196
    Helped
    26 / 26
    Points
    2,844
    Level
    12

    Re: What tool do I need for these connectors?

    I have bought one crimping tool that suits to this connector pin (CPU conector). Also there is provision to crimp Relimate connector too. This tool is of Ashwin make (Model - HT004). See the image. This is not a cheap tool. I had to part with INR2500. But quality of the product is superb.
    Last edited by swapan; 7th December 2016 at 12:19.

    •   AltAdvertisement

        
       

  4. #4
    Full Member level 5
    Points: 2,653, Level: 12
    Achievements:
    7 years registered

    Join Date
    Jan 2012
    Posts
    304
    Helped
    1 / 1
    Points
    2,653
    Level
    12

    Re: What tool do I need for these connectors?

    Sorry for not getting back to this thread. I think I'm going to have to buy a proper tool even at high expense. What are these connectors called exaclty? I'm not sure where to look :( I found the Ashwin HT004, but I couldn't find a price for it, do I have to request a price directly from Ashwin? The site that sells me these connectors is just a cheap site in Asia that give no information about what tool I need, I can send them an email though.

  5. #5
    Super Moderator
    Points: 260,224, Level: 100
    Awards:
    1st Helpful Member

    Join Date
    Jan 2008
    Location
    Bochum, Germany
    Posts
    45,441
    Helped
    13826 / 13826
    Points
    260,224
    Level
    100

    Re: What tool do I need for these connectors?

    The connectors look like replica of major manufacturers (e.g. Molex) types. Contacts may be identical to or different from the original, don't know.

    Expect a price of the original hand crimping tool in a 200 - 300 $ range. There are nevertheless cheap (about $20) tools from the Far East that might fit your connector series like the type below

    •   AltAdvertisement

        
       

  6. #6
    Super Moderator
    Points: 31,602, Level: 43
    ads-ee's Avatar
    Join Date
    Sep 2013
    Location
    USA
    Posts
    7,309
    Helped
    1719 / 1719
    Points
    31,602
    Level
    43

    Re: What tool do I need for these connectors?

    Quote Originally Posted by FvM
    Expect a price of the original hand crimping tool in a 200 - 300 $ range.
    They don't seem to be quite that expensive...
    http://www.newark.com/molex/63811-10...2in/dp/85C2464

    This is from the guys who invented that Molex connector...on the same page there appears to be the exact same crimp connector in your picture.

--[[ ]]--