+ Post New Thread
Results 1 to 8 of 8
  1. #1
    Member level 3
    Points: 651, Level: 5

    Join Date
    Aug 2016
    Posts
    62
    Helped
    0 / 0
    Points
    651
    Level
    5

    evaluation of S-parameter using HFSS

    hello
    how could i evaluate S parameters (db S11 AND S21 ) Versus Frequency plots in hfss..
    regards
    Bukero

    •   AltAdvertisement

        
       

  2. #2
    Junior Member level 1
    Points: 303, Level: 3

    Join Date
    Oct 2015
    Location
    's-Hertogenbosch
    Posts
    16
    Helped
    1 / 1
    Points
    303
    Level
    3

    Re: evaluation of S-parameter using HFSS

    S-parameter evaluation is a result of a sweep calculation for a driven modal setup. This is very basic fair which is is extensively treated in the first couple of tutorials. I would advice you follow these.



  3. #3
    Junior Member level 2
    Points: 516, Level: 4

    Join Date
    Nov 2016
    Posts
    21
    Helped
    2 / 2
    Points
    516
    Level
    4

    Re: evaluation of S-parameter using HFSS

    Hi in HFSS, once you define a port, you go to "Analysis" found in "Project manager" located at the left. Right click and "add solution setup", provide your solution frequency. Then a "setup1" will be instantly created. Then right click on "setup1" and "Add frequency sweep". Define your start and end frequency. Then run simulation (provided you completed other steps). After simulation, right click on "Results>create modal solution data report>rectangular plot> s-parameter" . There you have it , Select s11 or s21 and select dB under "function". Then, press "new report". Then the plot will be generated



    •   AltAdvertisement

        
       

  4. #4
    Member level 3
    Points: 651, Level: 5

    Join Date
    Aug 2016
    Posts
    62
    Helped
    0 / 0
    Points
    651
    Level
    5

    Re: evaluation of S-parameter using HFSS

    thanks dear
    i'm aware about that procedure but i couldn't get my required plots as for refractive index versus frequency, permitivity and permeability so for them do you have any suggestions?



  5. #5
    Full Member level 6
    Points: 3,554, Level: 14
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    US
    Posts
    350
    Helped
    103 / 103
    Points
    3,554
    Level
    14

    Re: evaluation of S-parameter using HFSS

    Hi Bukero,
    You need to write an expression for refractive index, permittivity and permeability in terms on SYZ parameters. If you have the expressions, you create an output variable and plot them with respect to frequency.

    If you are using Driven Modal solution, you take a look at the effective epsilon and lambda from the Matrix data.

    -sv


    1 members found this post helpful.

  6. #6
    Member level 3
    Points: 651, Level: 5

    Join Date
    Aug 2016
    Posts
    62
    Helped
    0 / 0
    Points
    651
    Level
    5

    Re: evaluation of S-parameter using HFSS

    thanks Sv1437
    one more doubt i have is that the equation i have to use for them are those which are available in texts or i have to develop a new one depeding on my model.



    •   AltAdvertisement

        
       

  7. #7
    Full Member level 6
    Points: 3,554, Level: 14
    Achievements:
    7 years registered

    Join Date
    Sep 2008
    Location
    US
    Posts
    350
    Helped
    103 / 103
    Points
    3,554
    Level
    14

    Re: evaluation of S-parameter using HFSS

    These should be standard equations available in text books / IEEE papers



  8. #8
    Member level 3
    Points: 651, Level: 5

    Join Date
    Aug 2016
    Posts
    62
    Helped
    0 / 0
    Points
    651
    Level
    5

    Re: evaluation of S-parameter using HFSS

    if possible can you please share link for a book or paper that includes these equations.
    Best Regards,
    Bukero



--[[ ]]--